Search by VIN / Frame, vehicle make, model, type, unit name, or by the part number of any oil:

Search
Toyota Opa

Oil for Toyota, Opa, Opa 2.0i d4 2WD (1AZ-FE/1AZ-FSE) (ACT10)

Toyota Model (Opa) to find out what kind of oil is used for it

Toyota Opa Opa 2.0i d4 2WD (1AZ-FE/1AZ-FSE) (ACT10)from 2000 to 2005 Engine oil, automatic transmission fluid, manual transmission oil, antifreeze, brake fluid, power steering fluid and other fluids.

Power:

Nodes and assemblies

Engine 1AZ-FE / 1AZ-FSE

Liquid volume (basic): 4.2 L
RAVENOL FO SAE 5W-30

RAVENOL FO SAE 5W-30

CleanSynto®
For engine

RAVENOL FO SAE 5W-30 is a synthetic, low-friction engine oil with CleanSynto® technology for passenger car gasoline and diesel engines, with and without turbocharging and direct injection.

Compliance with the requirements:
Fiat 9.55535-G1, Ford WSS-M2C 913-A, Ford WSS-M2C 913-B, Ford WSS-M2C 913-C, Ford WSS-M2C 913-D, Jaguar/Land Rover STJLR.03.5003, MB 229.6, Renault RN 0700, VWC 53036

Buy Online
Show more Hide details

SAE:  5W-30

API:  CF SL

ACEA:  A5 B5

  • Available packaging
  • Full description
  • Product parameters

Volume:
1 L

Vendor code:
1111115-001
1111115-001-01-999

Code:
4014835722613

Volume:
4 L

Vendor code:
1111115-004
1111115-004-01-999

Code:
4014835722699

Volume:
5 L

Vendor code:
1111115-005
1111115-005-01-999

Code:
4014835722651

Volume:
10 L

Vendor code:
1111115-010
1111115-010-01-999

Code:
4014835722644

Volume:
20 L

Vendor code:
1111115-020
1111115-020-01-999

Code:
4014835722620

Volume:
20 L, ecobox

Vendor code:
1111115-B20
1111115-B20-01-888

Code:
4014835772922

Volume:
60 L

Vendor code:
1111115-060
1111115-060-01-999

Code:
4014835722668

Volume:
60 L, print

Vendor code:
1111115-D60
1111115-D60-01-888

Code:
4014835722637

Volume:
208 L

Vendor code:
1111115-208
1111115-208-01-999

Code:
4014835722682

Volume:
208 L, print

Vendor code:
1111115-D28
1111115-D28-01-888

Code:
4014835722606

Volume:
1000 L

Vendor code:
1111115-700
 

RAVENOL FO SAE 5W-30 achieves a high viscosity index through its formulation with special base oils. The excellent cold start behaviour provides an optimum lubricating safety during the cold run phase.

Because of a considerable fuel saving RAVENOL FO SAE 5W-30 contributes to protect the environment by reducing the emissions.

RAVENOL FO SAE 5W-30 minimizes friction, wear and fuel consumption with excellent cold start characteristics.

Suitable for extended oil change intervals where recommended by manufacturer.

Application instructions

RAVENOL FO SAE 5W-30 is suitable as motor oil for fuel-efficient year-round use in modern petrol and diesel engines in passenger cars, station wagon's, vans and similar vehicles from FORD, RENAULT, Toyota, Hyundai, KIA, Mazda, Honda, Nissan und Mitsubishi.

Characteristics

  • Fuel economy in part and full power operation.
  • Very stable and excellent viscosity behaviour.
  • Excellent shear stability.
  • Excellent cold starting characteristics.
  • A safe lubricant film at high operating temperatures.
  • High wear and corrosion protection, high oxidation stability.
  • Prevention of sludge formation.
  • Excellent detergent- and dispersant characteristics.
  • Catalyst cleaning.
Parameter Unit Value Tests
SAE 5W-30
5W-30
Type Synthetic
Synthetic
API CF, SL
CF, SL
ACEA A5, B5
A5, B5
Recomendations Fiat 9.55535-G1, Ford WSS-M2C 913-A, Ford WSS-M2C 913-B, Ford WSS-M2C 913-C, Ford WSS-M2C 913-D, Jaguar/Land Rover STJLR.03.5003, MB 229.6, Renault RN 0700, VWC 53036
Fiat 9.55535-G1, Ford WSS-M2C 913-A, Ford WSS-M2C 913-B, Ford WSS-M2C 913-C, Ford WSS-M2C 913-D, Jaguar/Land Rover STJLR.03.5003, MB 229.6, Renault RN 0700, VWC 53036
Density at 20 °C g/cm³ 849 EN ISO 12185
849 g/cm³ EN ISO 12185
Color tan visual
tan visual
Viscosity at 100 °C mm²/s 10 DIN 51562-1
10 mm²/s DIN 51562-1
Viscosity at 40 °C mm²/s 56.6 DIN 51562-1
56.6 mm²/s DIN 51562-1
Viscosity Index VI 165 DIN ISO 2909
165 DIN ISO 2909
CCS Viscosity at -30 °C mPa*s 4300 ASTM D5293
4300 mPa*s ASTM D5293
Low Temp. Pumping viscosity (MRV) at -35 °C mPa*s 14.000 ASTM D4684
14.000 mPa*s ASTM D4684
Noack Volatility % 9.4 ASTM D5800
9.4 % ASTM D5800
tbn mgKOH/g 10.9 ASTM D2896
10.9 mgKOH/g ASTM D2896
Approvals Fiat 9.55535-G1, Ford WSS-M2C 913-A, Ford WSS-M2C 913-B, Ford WSS-M2C 913-C, Ford WSS-M2C 913-D, Jaguar/Land Rover STJLR.03.5003, MB 229.6, Renault RN0700, VWC 53036
Fiat 9.55535-G1, Ford WSS-M2C 913-A, Ford WSS-M2C 913-B, Ford WSS-M2C 913-C, Ford WSS-M2C 913-D, Jaguar/Land Rover STJLR.03.5003, MB 229.6, Renault RN0700, VWC 53036
Recommendations Fiat 9.55535-G1, Ford WSS-M2C913-A, Ford WSS-M2C913-B, Ford WSS-M2C913-C, Ford WSS-M2C913-D, Jaguar Land Rover STJLR.03.5003, MB 229.6, Renault RN0700, VWC 53036
Fiat 9.55535-G1, Ford WSS-M2C913-A, Ford WSS-M2C913-B, Ford WSS-M2C913-C, Ford WSS-M2C913-D, Jaguar Land Rover STJLR.03.5003, MB 229.6, Renault RN0700, VWC 53036
RAVENOL TSi SAE 10W-40

RAVENOL TSi SAE 10W-40

CleanSynto®
For engine

RAVENOL TSi SAE 10W-40 is a semi-synthetic CleanSynto® engine oil which allows an energy-saving operation because of its additivation, choice of base oils and viscosity adjustment. In order to guarantee the low viscosity of the SAE class 10W as well as a low evaporation loss RAVENOL TSi SAE 10W-40 is produced on the basis of hydro crack oils which correspond to the demands.

Manufacturer Approved:
BMW Special Oil

Compliance with the requirements:
MB 229.1, MB 229.3, VW 500.00, VW 501.01, VW 502.00, VW 505.00

Buy Online
Show more Hide details

SAE:  10W-40

API:  CF SN Plus SP

ACEA:  A3 B4

  • Available packaging
  • Full description
  • Product parameters

Volume:
1 L

Vendor code:
1112110-001
1112110-001-01-999

Code:
4014835724112

Volume:
4 L

Vendor code:
1112110-004
1112110-004-01-999

Code:
4014835724198

Volume:
5 L

Vendor code:
1112110-005
1112110-005-01-999

Code:
4014835724150

Volume:
10 L

Vendor code:
1112110-010
1112110-010-01-999

Code:
4014835724143

Volume:
20 L

Vendor code:
1112110-020
1112110-020-01-999

Code:
4014835724129

Volume:
20 L, ecobox

Vendor code:
1112110-B20
1112110-B20-01-888

Code:
4014835774520

Volume:
60 L

Vendor code:
1112110-060
1112110-060-01-999

Code:
4014835724167

Volume:
60 L, print

Vendor code:
1112110-D60
1112110-D60-01-888

Code:
4014835724136

Volume:
208 L, print

Vendor code:
1112110-D28
1112110-D28-01-888

Code:
4014835724105

Volume:
1000 L

Vendor code:
1112110-700
 

Volume:
208 L

Vendor code:
1112110-208
1112110-208-01-999

Code:
4014835724181

Extended oil change intervals according to manufacturer's instructions.

Application instructions

RAVENOL TSi SAE 10W-40 is suitable for all modern cars with petrol and diesel engines all the year; no sludge in the motor, excellent results during the test run. High engine cleanliness is guaranteed also in case of turbo charging and a complete catalyst operation as well as multi valves and diesel direct injections.

Characteristics

  • High abrasion resistance
  • Fuel saving because of easy running characteristics
  • Excellent detergent and dispersant characteristics
  • Prevention of black sludge creation
  • Long endurance because of high oxidation stability
  • Excellent cold start performance
  • Very good viscosity temperature behaviour
  • Low evaporation
  • Suitable for catalysts
Parameter Unit Value Tests
SAE 10W-40
10W-40
Type Semi-synthetic
Semi-synthetic
API CF, SN Plus, SP
CF, SN Plus, SP
ACEA A3, B4
A3, B4
Manufacturer Approved BMW Special Oil
BMW Special Oil
Recomendations MB 229.1, MB 229.3, VW 500.00, VW 501.01, VW 502.00, VW 505.00
MB 229.1, MB 229.3, VW 500.00, VW 501.01, VW 502.00, VW 505.00
Density at 20 °C g/cm³ 862 EN ISO 12185
862 g/cm³ EN ISO 12185
Color Brown visual
Brown visual
Viscosity at 100 °C mm²/s 14.5 DIN 51562-1
14.5 mm²/s DIN 51562-1
Viscosity at 40 °C mm²/s 97.7 DIN 51562-1
97.7 mm²/s DIN 51562-1
Viscosity Index VI 153 DIN ISO 2909
153 DIN ISO 2909
CCS Viscosity at -25 °C mPa*s 5940 ASTM D5293
5940 mPa*s ASTM D5293
Low Temp. Pumping viscosity (MRV) at -30 °C mPa*s 20.800 ASTM D4684
20.800 mPa*s ASTM D4684
Noack Volatility % 9.5 ASTM D5800
9.5 % ASTM D5800
tbn mgKOH/g 10 ASTM D2896
10 mgKOH/g ASTM D2896
Approvals BMW Special Oil, MB 229.1, MB 229.3, VW 500.00, VW 501.01, VW 502.00, VW 505.00
BMW Special Oil, MB 229.1, MB 229.3, VW 500.00, VW 501.01, VW 502.00, VW 505.00
Recommendations MB 229.1, MB 229.3, VW 500 00, VW 501 01, VW 502 00, VW 505 00
MB 229.1, MB 229.3, VW 500 00, VW 501 01, VW 502 00, VW 505 00
RAVENOL LLO SAE 10W-40

RAVENOL LLO SAE 10W-40

CleanSynto®
For engine

RAVENOL LLO SAE 10W-40 is a semi-synthetic high-performance light-running engine oil with CleanSynto® technology for passenger car carburetor and diesel engines with and without turbocharging and direct injection. Minimizing friction, wear and fuel consumption, excellent cold start characteristics. Extended oil change intervals according to the manufacturer's instructions.

Compliance with the requirements:
BMW Special Oil, MB 229.1, Renault RN 0700, VW 500.00, VW 501.01, VW 505.00

Buy Online
Show more Hide details

SAE:  10W-40

API:  CF SN

ACEA:  A3 B4

  • Available packaging
  • Full description
  • Product parameters

Volume:
1 L

Vendor code:
1112112-001
1112112-001-01-999

Code:
4014835724310

Volume:
4 L

Vendor code:
1112112-004
1112112-004-01-999

Code:
4014835724396

Volume:
5 L

Vendor code:
1112112-005
1112112-005-01-999

Code:
4014835724358

Volume:
10 L

Vendor code:
1112112-010
1112112-010-01-999

Code:
4014835724341

Volume:
20 L

Vendor code:
1112112-020
1112112-020-01-999

Code:
4014835724327

Volume:
20 L, ecobox

Vendor code:
1112112-B20
1112112-B20-01-888

Code:
4014835774728

Volume:
60 L

Vendor code:
1112112-060
1112112-060-01-999

Code:
4014835724365

Volume:
60 L, print

Vendor code:
1112112-D60
1112112-D60-01-888

Code:
4014835724334

Volume:
208 L

Vendor code:
1112112-208
1112112-208-01-999

Code:
4014835724389

Volume:
208 L, print

Vendor code:
1112112-D28
1112112-D28-01-888

Code:
4014835724303

Volume:
1000 L

Vendor code:
1112112-700
1112112-700-01-999

RAVENOL LLO SAE 10W-40 is produced on the basis of hydro crack oils which correspond to the high tech demands.

Application instructions

RAVENOL LLO SAE 10W-40 is suitable for the use of all modern cars with Otto and Diesel engines all the year; no sludge in the motor, excellent results during the test run. A high engine cleanness is guaranteed also in case of turbo charging and a complete catalyst operation as well as multi valves and diesel direct injections.

Characteristics

  • High abrasion resistance
  • Fuel saving because of easy running characteristics
  • Excellent detergent and dispersant characteristics
  • Prevention of black sludge creation
  • Long endurance because of high oxidation stability
  • An excellent cold start performance
  • A very good viscosity temperature behaviour
  • Low evaporation
  • Suitable for catalysts
Parameter Unit Value Tests
SAE 10W-40
10W-40
Type Semi-synthetic
Semi-synthetic
API CF, SN
CF, SN
ACEA A3, B4
A3, B4
Recomendations BMW Special Oil, MB 229.1, Renault RN 0700, VW 500.00, VW 501.01, VW 505.00
BMW Special Oil, MB 229.1, Renault RN 0700, VW 500.00, VW 501.01, VW 505.00
Density at 20 °C g/cm³ 854 EN ISO 12185
854 g/cm³ EN ISO 12185
Color tan visual
tan visual
Viscosity at 100 °C mm²/s 15 DIN 51562-1
15 mm²/s DIN 51562-1
Viscosity at 40 °C mm²/s 96.4 DIN 51562-1
96.4 mm²/s DIN 51562-1
Viscosity Index VI 164 DIN ISO 2909
164 DIN ISO 2909
CCS Viscosity at -25 °C mPa*s 4300 ASTM D5293
4300 mPa*s ASTM D5293
Low Temp. Pumping viscosity (MRV) at -30 °C mPa*s 19.200 ASTM D4684
19.200 mPa*s ASTM D4684
Noack Volatility % 10.5 ASTM D5800
10.5 % ASTM D5800
tbn mgKOH/g 10.8 ASTM D2896
10.8 mgKOH/g ASTM D2896
Approvals BMW Special Oil, MB 229.1, Renault RN0700, VW 500.00, VW 501.01, VW 505.00
BMW Special Oil, MB 229.1, Renault RN0700, VW 500.00, VW 501.01, VW 505.00
Recommendations BMW Special Oil, MB 229.1, Renault RN0700, VW 500 00, VW 501 01, VW 505 00
BMW Special Oil, MB 229.1, Renault RN0700, VW 500 00, VW 501 01, VW 505 00
RAVENOL TSJ SAE 10W-30

RAVENOL TSJ SAE 10W-30

CleanSynto®
For engine

RAVENOL TSJ SAE 10W-30 is a semi-synthetic low friction motor oil with CleanSynto® technology for passenger car petrol and diesel engines with and without turbo-charging and direct injection. Formulated to minimise friction, wear and fuel consumption with excellent cold start characteristics. Suitable for extended oil change intervals where recommended by manufacturer.

Compliance with the requirements:
Chrysler MS-6395, Fiat 9.55535-CR1

Buy Online
Show more Hide details

SAE:  10W-30

API:  SQ (RC)

ILSAC:  GF-7A

  • Available packaging
  • Full description
  • Product parameters

Volume:
1 L

Vendor code:
1112106-001
1112106-001-01-999

Code:
4014835724013

Volume:
4 L

Vendor code:
1112106-004
1112106-004-01-999

Code:
4014835724099

Volume:
5 L

Vendor code:
1112106-005
1112106-005-01-999

Code:
4014835724051

Volume:
10 L

Vendor code:
1112106-010
1112106-010-01-999

Code:
4014835852464

Volume:
20 L

Vendor code:
1112106-020
 

Volume:
20 L, ecobox

Vendor code:
1112106-B20
1112106-B20-01-888

Code:
4014835774421

Volume:
60 L

Vendor code:
1112106-060
 

Volume:
60 L, print

Vendor code:
1112106-D60
1112106-D60-01-888

Code:
4014835724037

Volume:
208 L

Vendor code:
1112106-028
1112106-208-01-888

Code:
4014835724006

Volume:
208 L

Vendor code:
1112106-208
 

Volume:
208 L, print

Vendor code:
1112106-D28
1112106-D28-01-888

Volume:
1000 L

Vendor code:
1112106-700
 

RAVENOL TSJ SAE 10W-30 is especially produced for the use in cars of Japanese and Asian manufacturers.

Application instructions

RAVENOL TSJ SAE 10W-30 is suitable for the use in all modern cars of Japanese and Asian manufacturers all the year.

Characteristics

  • An universal use in all modern petrol and diesel engines
  • A quick lubrication of the engine even at low temperatures
  • A low evaporation tendency, therefore a low oil consumption
  • Safety against sludge accumulations, cokings and corrosion even under unfavourable operating conditions
  • Guarantee of the function of the hydro tappets at all temperatures
  • No oil limited deposits in combustion chambers, at the piston ring and valves
  • Unchanged viscosity during the whole oil change interval, a high viscosity index
  • Neutral behaviour against sealing materials
Parameter Unit Value Tests
SAE 10W-30
10W-30
Type Semi-synthetic
Semi-synthetic
API SQ (RC)
SQ (RC)
ILSAC GF-7A
GF-7A
Recomendations Chrysler MS-6395, Fiat 9.55535-CR1
Chrysler MS-6395, Fiat 9.55535-CR1
Suitable for Daewoo, Daihatsu, Honda, Hyundai, Isuzu, KIA, Mazda, Mitsubishi, Nissan, SsangYong, Subaru, Suzuki, Toyota
Daewoo, Daihatsu, Honda, Hyundai, Isuzu, KIA, Mazda, Mitsubishi, Nissan, SsangYong, Subaru, Suzuki, Toyota
Density at 20 °C g/cm³ 854 EN ISO 12185
854 g/cm³ EN ISO 12185
Color tan visual
tan visual
Viscosity at 100 °C mm²/s 10.2 DIN 51562-1
10.2 mm²/s DIN 51562-1
Viscosity at 40 °C mm²/s 64.3 DIN 51562-1
64.3 mm²/s DIN 51562-1
Viscosity Index VI 145 DIN ISO 2909
145 DIN ISO 2909
CCS Viscosity at -25 °C mPa*s 4830 ASTM D5293
4830 mPa*s ASTM D5293
Low Temp. Pumping viscosity (MRV) at -30 °C mPa*s 11.300 ASTM D4684
11.300 mPa*s ASTM D4684
Noack Volatility % 9.9 ASTM D5800
9.9 % ASTM D5800
tbn mgKOH/g 7.4 ASTM D2896
7.4 mgKOH/g ASTM D2896
Approvals Chrysler MS-6395, Fiat 9.55535-CR1
Chrysler MS-6395, Fiat 9.55535-CR1
Recommendations Chrysler MS-6395, Daewoo, Daihatsu, Fiat 9.55535-CR1, Honda, Hyundai, Isuzu, KIA, Mazda, Mitsubishi, Nissan, SsangYong, Subaru, Suzuki, Toyota
Chrysler MS-6395, Daewoo, Daihatsu, Fiat 9.55535-CR1, Honda, Hyundai, Isuzu, KIA, Mazda, Mitsubishi, Nissan, SsangYong, Subaru, Suzuki, Toyota
RAVENOL HDX SAE 5W-30

RAVENOL HDX SAE 5W-30

CleanSynto®
For engine

RAVENOL HDX SAE 5W-30 is a synthetic, low-friction engine oil with CleanSynto® technology for car gasoline engines, with and without turbocharging and direct injection, such as Turbo-GDI and direct injection.

Manufacturer Approved:
GM dexos1® Gen 1, GM dexos1® Gen 2, GM dexos1® Gen 3

Compliance with the requirements:
Chrysler MS-13340, Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C 929-A, Ford WSS-M2C 946-A, Ford WSS-M2C 946-B1, Ford WSS-M2C 961-A1, Honda/Acura HTO-06, Opel OV 040 1547 - G30, VWC 53034

Show more Hide details

SAE:  5W-30

API:  SQ (RC)

ILSAC:  GF-7A

  • Available packaging
  • Full description
  • Product parameters

Volume:
1 L

Vendor code:
1111125-001
1111125-001-01-999

Code:
4014835858541

Volume:
4 L

Vendor code:
1111125-004
1111125-004-01-999

Code:
4014835858572

Volume:
5 L

Vendor code:
1111125-005
1111125-005-01-999

Code:
4014835858602

Volume:
10 L

Vendor code:
1111125-010
1111125-010-01-999

Code:
4014835858633

Volume:
20 L

Vendor code:
1111125-020
1111125-020-01-999

Code:
4014835858671

Volume:
20 L, ecobox

Vendor code:
1111125-B20
1111125-B20-01-888

Code:
4014835858657

Volume:
60 L

Vendor code:
1111125-060
1111125-060-01-999

Code:
4014835858718

Volume:
60 L, print

Vendor code:
1111125-D60
 

Volume:
208 L

Vendor code:
1111125-208
1111125-208-01-999

Code:
4014835858756

Volume:
208 L, print

Vendor code:
1111125-D28
 

Volume:
1000 L

Vendor code:
1111125-700
 

With its new formulation, RAVENOL HDX SAE 5W-30 provides a safe layer of lubrication even at very high operating temperatures and protects from corrosion and loss of oil through oxidation or coking.

RAVENOL HDX SAE 5W-30 achieves a high viscosity index through its formulation with special base oils. The excellent cold start behaviour provides an optimum lubricating safety during the cold run phase.

Because of a considerable fuel saving RAVENOL HDX SAE 5W-30 contributes to protect the environment by reducing the emissions.

RAVENOL HDX SAE 5W-30 minimizes friction, wear and fuel consumption with excellent cold start characteristics.

RAVENOL HDX SAE 5W-30 helps to avoid low speed pre-ignition LSPI (Low Speed ​​Pre-ignition). This can help avoid engine damage.

Suitable for extended oil change intervals where recommended by manufacturer.

Application instructions

RAVENOL HDX SAE 5W-30 is a high-performance low-friction engine oil for modern engines. It is recommended by OPEL/GENERAL MOTORS corresponding to dexos1 specification for modern car engines under all operating conditions.

RAVENOL HDX SAE 5W-30 is also suitable for the shown specifications of Ford, Chrysler and Fiat.

Characteristics

  • Fuel savings in partial and full load operation
  • Outstanding wear protection and high viscosity index ensure engine longevity, even under high-speed driving conditions
  • Excellent cold-start properties even at low temperatures below -25°C
  • A safe lubricating film at high operating temperatures
  • Low evaporation tendency, thus low oil consumption
  • No oil-based deposits in combustion chambers, in the piston ring zone and on valves
  • Neutrality towards sealing materials
  • Extended oil change intervals protect natural resources
Parameter Unit Value Tests
SAE 5W-30
5W-30
Type Synthetic
Synthetic
API SQ (RC)
SQ (RC)
ILSAC GF-7A
GF-7A
Manufacturer Approved GM dexos1® Gen 1, GM dexos1® Gen 2, GM dexos1® Gen 3
GM dexos1® Gen 1, GM dexos1® Gen 2, GM dexos1® Gen 3
Recomendations Chrysler MS-13340, Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C 929-A, Ford WSS-M2C 946-A, Ford WSS-M2C 946-B1, Ford WSS-M2C 961-A1, Honda/Acura HTO-06, Opel OV 040 1547 - G30, VWC 53034
Chrysler MS-13340, Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C 929-A, Ford WSS-M2C 946-A, Ford WSS-M2C 946-B1, Ford WSS-M2C 961-A1, Honda/Acura HTO-06, Opel OV 040 1547 - G30, VWC 53034
Density at 20 °C g/cm³ 844 EN ISO 12185
844 g/cm³ EN ISO 12185
Color tan visual
tan visual
Viscosity at 100 °C mm²/s 10.8 DIN 51562-1
10.8 mm²/s DIN 51562-1
Viscosity at 40 °C mm²/s 59.8 DIN 51562-1
59.8 mm²/s DIN 51562-1
Viscosity Index VI 173 DIN ISO 2909
173 DIN ISO 2909
CCS Viscosity at -30 °C mPa*s 3630 ASTM D5293
3630 mPa*s ASTM D5293
Low Temp. Pumping viscosity (MRV) at -35 °C mPa*s 13.500 ASTM D4684
13.500 mPa*s ASTM D4684
Noack Volatility % 8.1 ASTM D5800
8.1 % ASTM D5800
tbn mgKOH/g 7.8 ASTM D2896
7.8 mgKOH/g ASTM D2896
Approvals Chrysler MS-13340, Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C 929-A, Ford WSS-M2C 946-A, Ford WSS-M2C 946-B1, Ford WSS-M2C 961-A1, GM dexos1® Gen 1, GM dexos1® Gen 2, GM dexos1® Gen 3, Honda/Acura HTO-06, Opel OV 040 1547 - G30, VWC 53034
Chrysler MS-13340, Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C 929-A, Ford WSS-M2C 946-A, Ford WSS-M2C 946-B1, Ford WSS-M2C 961-A1, GM dexos1® Gen 1, GM dexos1® Gen 2, GM dexos1® Gen 3, Honda/Acura HTO-06, Opel OV 040 1547 - G30, VWC 53034
Recommendations Chrysler MS-13340, Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C929-A, Ford WSS-M2C946-A, Ford WSS-M2C946-B1, Ford WSS-M2C961-A1, Honda/Acura HTO-06, Opel OV 040 1547 - G30, VWC 53034
Chrysler MS-13340, Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C929-A, Ford WSS-M2C946-A, Ford WSS-M2C946-B1, Ford WSS-M2C961-A1, Honda/Acura HTO-06, Opel OV 040 1547 - G30, VWC 53034
RAVENOL SMO SAE 5W-30

RAVENOL SMO SAE 5W-30

CleanSynto®
Engine oil

RAVENOL SMO SAE 5W-30 Synthetic Multi Oil is synthetic low friction motor oil with CleanSynto® technology for passenger car gasoline engines with and without turbo-charging and direct injection.

Compliance with the requirements:
Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C 929-A, Ford WSS-M2C 946-A, GM 6094 M

Show more Hide details

SAE:  5W-30

API:  SQ (RC)

ILSAC:  GF-7A

  • Available packaging
  • Full description
  • Product parameters

Volume:
1 L

Vendor code:
1111151-001
1111151-001-01-999

Code:
4014835860117

Volume:
4 L

Vendor code:
1111151-004
1111151-004-01-999

Code:
4014835860148

Volume:
5 L

Vendor code:
1111151-005
1111151-005-01-999

Code:
4014835860179

Volume:
20 L

Vendor code:
1111151-020
1111151-020-01-999

Code:
4014835867710

Volume:
20 L, ecobox

Vendor code:
1111151-B20
1111151-B20-01-888

Code:
4014835862807

Volume:
60 L

Vendor code:
1111151-060
1111151-060-01-999

Volume:
60 L, print

Vendor code:
1111151-D60
 

Volume:
208 L

Vendor code:
1111151-208
1111151-208-01-999

Code:
4014835860209

Volume:
208 L, print

Vendor code:
1111151-D28
 

RAVENOL SMO SAE 5W-30 achieves a high viscosity index through its formulation with special base oils. The excellent cold start behaviour provides an optimum lubricating safety during the cold run phase.

Because of a considerable fuel saving RAVENOL SMO SAE 5W-30 contributes to protect the environment by reducing the emissions.

RAVENOL SMO SAE 5W-30 minimizes friction, wear and fuel consumption with excellent cold start characteristics. Suitable for extended oil change intervals where recommended by manufacturer.

Application instructions

RAVENOL SMO SAE 5W-30 is suitable for demanding engines as high performance low friction engine oil. The specifications API SQ Resource Conserving (RC) and ILSAC GF-7A are backward compatible with the respective previous specifications.

Characteristics

  • Fuel economy in part and full power operation
  • Excellent wear protection and high viscosity index also under high-speed driving conditions, the long life of the engine
  • Excellent cold starting characteristics also at low temperatures below -30°C
  • A safe lubricant film at high operating temperatures
  • Low evaporative tendency, so lower oil consumption
  • No deposits in combustion chambers, in the piston ring zone and valves
  • Neutrality towards sealing materials
  • Extended oil change intervals to protect natural resources
Parameter Unit Value Tests
SAE 5W-30
5W-30
Type Synthetic
Synthetic
API SQ (RC)
SQ (RC)
ILSAC GF-7A
GF-7A
Recomendations Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C 929-A, Ford WSS-M2C 946-A, GM 6094 M
Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C 929-A, Ford WSS-M2C 946-A, GM 6094 M
Suitable for Lexus, Mazda, Nissan, Subaru, Toyota
Lexus, Mazda, Nissan, Subaru, Toyota
Density at 20 °C g/cm³ 848 EN ISO 12185
848 g/cm³ EN ISO 12185
Color tan visual
tan visual
Viscosity at 100 °C mm²/s 10.3 DIN 51562-1
10.3 mm²/s DIN 51562-1
Viscosity at 40 °C mm²/s 60.1 DIN 51562-1
60.1 mm²/s DIN 51562-1
Viscosity Index VI 162 DIN ISO 2909
162 DIN ISO 2909
CCS Viscosity at -30 °C mPa*s 5700 ASTM D5293
5700 mPa*s ASTM D5293
Low Temp. Pumping viscosity (MRV) at -35 °C mPa*s 18.900 ASTM D4684
18.900 mPa*s ASTM D4684
Noack Volatility % 9.6 ASTM D5800
9.6 % ASTM D5800
tbn mgKOH/g 7.4 ASTM D2896
7.4 mgKOH/g ASTM D2896
Approvals Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C 929-A, Ford WSS-M2C 946-A, GM 6094M
Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C 929-A, Ford WSS-M2C 946-A, GM 6094M
Recommendations Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C929-A, Ford WSS-M2C946-A, GM 6094M, Lexus, Mazda, Nissan, Subaru, Toyota
Chrysler MS-6395, Fiat 9.55535-CR1, Ford WSS-M2C929-A, Ford WSS-M2C946-A, GM 6094M, Lexus, Mazda, Nissan, Subaru, Toyota
RAVENOL Professional Engine Cleaner

RAVENOL Professional Engine Cleaner

RAVENOL Professional Engine Cleaner is active concentrate for longer oil cleanliness for all petrol and diesel engines (with and without catalytic converter).

Show more Hide details
  • Available packaging
  • Full description
  • Product parameters

Volume:
300 ml

Vendor code:
1390323-300
1390323-300-05-999

Code:
4014835889378

RAVENOL Professional Engine Cleaner can also be used in motorcycles.

RAVENOL Professional Engine Cleaner effectively breaks down dirt accumulation and sludge deposits in the engine compartment using intensive-cleaning tensides and removes these effectively when draining used oil.

RAVENOL Professional Engine Cleaner cleans and rinses the entire engine system.

Application instructions

RAVENOL Professional Engine Cleaner is added to the warm motor oil.

Area of application:

-If black sludge is suspected

-In the event of hydraulic tappets rattling

-In the event of delayed oil change

-For soiled engines or used oil

-Preventively at every oil change to avoid contamination of the engine

-Also suitable for oldtimers and engines with belts running in the oil system (wet belts)

 

Dosage: 300 ml RAVENOL Professional Engine Cleaner are sufficient for one application of approx. 5L Oil, regardless of manufacturer and motor size.

 

Application: Add the contents to the warm motor oil before changing oil. Do not go below the minimum oil level. For maximum effect, allow to run for up to 10 minutes. Afterwards, immediately replace oil and filter.

 

RAVENOL Professional Engine Cleaner is tried and tested for aggregates with motor oils based on mineraloil and synthetic oil.

Characteristics

  • Long-term effectiveness and clean fresh oil
  • Remedy for soiled engines
  • Protection against compression loss in the area of the piston rings
  • Leads to better exhaust emissions and increases the performance of the engine
Parameter Unit Value Tests
Viscosity at 40 °C mm²/s 5 DIN EN ISO 3104
5 mm²/s DIN EN ISO 3104
Color Yellow visual
Yellow visual

CVT gearbox in a unit with final drive K110

Liquid volume (basic): 9 L
RAVENOL CVT KFE Fluid

RAVENOL CVT KFE Fluid

For transmission

RAVENOL CVT KFE Fluid is a synthetic CVT (Continuously Variable Transmission) Fluid, designed on the basis of high quality hydrocrack oils with a special additive and inhibition, which ensure a perfect function of the transmission.

Show more Hide details
  • Available packaging
  • Full description
  • Product parameters

Volume:
1 L

Vendor code:
1211134-001
1211134-001-01-999

Code:
4014835803718

Volume:
4 L

Vendor code:
1211134-004
1211134-004-01-999

Code:
4014835803725

Volume:
20 L, ecobox

Vendor code:
1211134-B20
 

RAVENOL CVT KFE Fluid is a synthetic CVT transmission fluid with low viscosity for Toyota CVT transmission.

RAVENOL CVT KFE Fluid guarantees an optimum of power transmission.

Application instructions

RAVENOL CVT KFE Fluid was developed for use in CVT transmission (Steel Belt Continuously Variable Transmission), especially for Toyota transmissions.

RAVENOL CVT KFE Fluid ensures a stable viscosity under high mechanical stress in the transmission elements (push belt).

Characteristics

  • Very good lubricating ability even at low temperatures in winter
  • A high, stable viscosity index
  • Very low pour point
  • Very good oxidation stability
  • Protection against corrosion and foam formation
  • Good balanced coefficient of friction
  • Neutral behaviour towards sealing materials
  • Neutral behaviour by inhibition to non-ferrous metals
Parameter Unit Value Tests
Type Synthetic
Synthetic
Color Red visual
Red visual
Density at 20 °C g/cm³ 829 EN ISO 12185
829 g/cm³ EN ISO 12185
Recommendations Toyota 08886-02503, Toyota 08886-02505
Toyota 08886-02503, Toyota 08886-02505

Power steering

Liquid volume (basic): 0.8 L
RAVENOL Hydraulik PSF Fluid

RAVENOL Hydraulik PSF Fluid

For power steering

RAVENOL Hydraulik PSF Fluid is a specific synthetic hydraulic fluid for power steering.

Compliance with the requirements:
Honda PSF-S, KIA PSF-III, Mazda PSF, Mitsubishi DIAMOND PSF-2M, Subaru PS Fluid, Toyota PSF-EH

Buy Online
Show more Hide details
  • Available packaging
  • Full description
  • Product parameters

Volume:
20 L

Vendor code:
1181000-020
 

Volume:
1 L

Vendor code:
1181000-001
1181000-001-01-999

Code:
4014835736313

Volume:
4 L

Vendor code:
1181000-004
1181000-004-01-999

Code:
4014835736399

Volume:
10 L

Vendor code:
1181000-010
1181000-010-01-999

Code:
4014835736344

Volume:
20 L, ecobox

Vendor code:
1181000-B20
1181000-B20-01-888

Code:
4014835784222

Volume:
60 L

Vendor code:
1181000-060
 

Volume:
208 L

Vendor code:
1181000-208
1181000-208-01-999

Code:
4014835736382

Volume:
1000 L

Vendor code:
1181000-700
 

RAVENOL Hydraulik PSF Fluid is guaranteeing an optimized power transmission.

RAVENOL Hydraulik PSF Fluid is produced on the basis of high quality base oils with special additives and inhibition which guarantees a perfect function of the hydraulics.

Application instructions

RAVENOL Hydraulik PSF Fluid is especially developed for the use as a hydraulic fluid in power transmissions.

Characteristics

  • A very low pour point
  • An excellent foam prevention, no foam formation
  • A good lubricating ability even at low temperatures in winter
  • A high, stable viscosity index
  • A very good oxidation stability
  • Excellent protection against wear and tear, corrosion and foam formation
  • Fine tuned coefficient of friction
  • eutral behaviour against sealing materials
  • Neutral behaviour because of inhibition against non ferrous metals
Parameter Unit Value Tests
Type Synthetic
Synthetic
Recomendations Honda PSF-S, KIA PSF-III, Mazda PSF, Mitsubishi DIAMOND PSF-2M, Subaru PS Fluid, Toyota PSF-EH
Honda PSF-S, KIA PSF-III, Mazda PSF, Mitsubishi DIAMOND PSF-2M, Subaru PS Fluid, Toyota PSF-EH
Suitable for PSA 4007
PSA 4007
Density at 20 °C g/cm³ 847 EN ISO 12185
847 g/cm³ EN ISO 12185
Color Red visual
Red visual
Viscosity at 100 °C mm²/s 7.2 DIN 51562-1
7.2 mm²/s DIN 51562-1
Viscosity at 40 °C mm²/s 34.8 DIN 51562-1
34.8 mm²/s DIN 51562-1
Viscosity Index VI 178 DIN ISO 2909
178 DIN ISO 2909
Brookfield Viscosity at -40 °C mPa*s 12800 ASTM D2983
12800 mPa*s ASTM D2983
Approvals Honda PSF-S, KIA PSF-III, Mazda PSF, Mitsubishi DIAMOND PSF-2M, Subaru PS Fluid, Toyota PSF-EH
Honda PSF-S, KIA PSF-III, Mazda PSF, Mitsubishi DIAMOND PSF-2M, Subaru PS Fluid, Toyota PSF-EH
Recommendations Citroën/Peugeot 9735EJ für C-Crosser, Peugeot 4007, Honda PSF-S, Hyundai PSF-3, KIA PSF-III, Mazda PSF, Mitsubishi Diamond PSF-2M, Peugeot 4007, Subaru PS Fluid, Toyota PSF-EH
Citroën/Peugeot 9735EJ für C-Crosser, Peugeot 4007, Honda PSF-S, Hyundai PSF-3, KIA PSF-III, Mazda PSF, Mitsubishi Diamond PSF-2M, Peugeot 4007, Subaru PS Fluid, Toyota PSF-EH

Hydraulic brakes

Liquid volume (basic): 1 L
RAVENOL DOT 4

RAVENOL DOT 4

RAVENOL DOT 4 is a brake fluid for the use in all vehicles with optimum ABS characteristics. There is a chemical stability and it is provided with additives which save the best lubrication efficiency.

Show more Hide details
  • Available packaging
  • Full description
  • Product parameters

Volume:
250 ml

Vendor code:
1350611-250
1350611-250-05-555

Code:
4014835903739

Volume:
1 L

Vendor code:
1350611-001
1350611-001-01-555

Code:
4014835903760

Volume:
20 L

Vendor code:
1350611-020
 

Volume:
500 ml

Vendor code:
1350611-500
1350611-500-05-555

Code:
4014835903821

Because of the special formulation of RAVENOL DOT 4 the international specifications SAE J 1704, ISO 4925 and the safety regulations FMVSS 116 DOT 3 and DOT 4 from the United States of America are exceeded.

Application instructions

RAVENOL DOT can be used in all vehicles for which the DOT 4 specification for brake fluids is required. It is suitable for all hydraulic brake systems with synthetic fluids.

RAVENOL DOT is miscible with all known brake fluids of the same specification. To use the high performance level of RAVENOL DOT , a complete change of the brake fluid is recommended.

RAVENOL DOT is not suitable for vehicles with mineral oil systems (e.g. certain Citroën models).

FOLLOW VEHICLE MANUFACTURERS RECOMMENDATIONS WHEN ADDING BRAKE FLUID KEEP BRAKE FLUID CLEAN AND DRY. Contamination with dirt, water, petroleum products or other materials may result in brake failure or costly repairs.

STORE BRAKE FLUID ONLY IN ITS ORIGINAL CONTAINER. KEEP CONTAINER CLEAN AND TIGHTLY CLOSED TO PREVENT ADSORPTION OF WATER. CAUTION! DO NOT REFILL CONTAINER AND DO NOT USE FOR OTHER LIQUIDS.

Dispose of used brake fluid responsibly (EU waste code 160113).

Brake fluid damages paint work –if spilt wash off immediately with plenty of water.

Characteristics

  • optimum ABS characteristics
  • chemical stability
  • best lubrication efficiency
  • neutral behaviour regarding brake parts
  • low viscosity at low temperatures
  • miscible with all brake fluids of the same specifications
Parameter Unit Value Tests
Type Synthetic
Synthetic
specification DOT 4, ISO 4925 Class 4, SAE J 1704
DOT 4, ISO 4925 Class 4, SAE J 1704
Density at 20 °C g/cm³ 1052 EN ISO 12185
1052 g/cm³ EN ISO 12185
Color light yellow visual
light yellow visual
Viscosity at 100 °C mPa*s 2.41 ASTM D445
2.41 mPa*s ASTM D445
Viscosity at -40 °C cSt 1340 ASTM D445
1340 cSt ASTM D445
Wet Equilibrium Reflux Boiling Point °C 169 FMVSS 116
169 °C FMVSS 116
High Temperature Stability °C -1 FMVSS 116
-1 °C FMVSS 116
Chemical Stability °C 1 FMVSS 116
1 °C FMVSS 116
Evaporation %w/w 61 FMVSS 116
61 %w/w FMVSS 116
Fluidity & Appearance at -40 °C i.O., 4s FMVSS 116
i.O., 4s FMVSS 116
Fluidity & Appearance at -50 °C i.O., 8s FMVSS 116
i.O., 8s FMVSS 116
Water Tolerance at -40 °C transparent, 3s FMVSS 116
transparent, 3s FMVSS 116
Water Tolerance at +60 °C Transparent FMVSS 116
Transparent FMVSS 116
Compatibility at -40 °C Transparent FMVSS 116
Transparent FMVSS 116
Compatibility at +60 °C Transparent FMVSS 116
Transparent FMVSS 116
Tinned Iron Δ mg/cm² 0.04 FMVSS 116
0.04 Δ mg/cm² FMVSS 116
Steel mg/cm² -0.01 FMVSS 116
-0.01 mg/cm² FMVSS 116
Aluminium mg/cm² 0.02 FMVSS 116
0.02 mg/cm² FMVSS 116
Cast Iron Δ mg/cm² -0,03 FMVSS 116
-0,03 Δ mg/cm² FMVSS 116
Brass mg/cm² -0.08 FMVSS 116
-0.08 mg/cm² FMVSS 116
Copper mg/cm² -0.05 FMVSS 116
-0.05 mg/cm² FMVSS 116
Zinc mg/cm² 0.01 FMVSS 116
0.01 mg/cm² FMVSS 116
Rubber Diameter Change 0.16 FMVSS 116
0.16 FMVSS 116
Hardness Change °IRHD -4 FMVSS 116
-4 °IRHD FMVSS 116
Appearance i.O. FMVSS 116
i.O. FMVSS 116
SBR at 70 °C mm 0.56 FMVSS 116
0.56 mm FMVSS 116
SBR at 120 °C mm 0.73 FMVSS 116
0.73 mm FMVSS 116
EPDM at 70 °C (as required by SAE J1703) IRHD -2 FMVSS 116
-2 IRHD FMVSS 116
EPDM at 120 °C IRHD -2 FMVSS 116
-2 IRHD FMVSS 116
Natural at 70 °C (as required by ISO 4925) mm 0.38 FMVSS 116
0.38 mm FMVSS 116
Approvals DOT 4, ISO 4925 Class 4, SAE J 1704
DOT 4, ISO 4925 Class 4, SAE J 1704

Cooling system

Liquid volume (basic): 5.8 L
RAVENOL OTC Premix -40°C Protect C12+

RAVENOL OTC Premix -40°C Protect C12+

Coolant

RAVENOL OTC Organic Techn. Coolant Premix -40°C is a ready-to-use, prediluted with water, eco-friendly 1.2- Ethanediol (monoethylene glycol) based silicate, borate, nitrite, amine and phosphate-free coolant for cooling circuits in combustion engines which provides maintenance-free corrosion and frost protection. This product is formulated based on a proven inhibitor development with the organic additive technology OAT as an extended life coolant.

Compliance with the requirements:
DAF 74002, DTFR 29C110 (MB 325.3), DTFR 29D110 (MB 326.3), Deutz DQC CB-14, Ford WSS-M97 B44-D, GM 6277 M, GM B0401065, MAN 324 Type SNF, MB 325.3, MB 326.3, SAE J 1034, VW G 012 A8F, VW TL 774-D, VW TL 774-F, Volvo VCS

Show more Hide details
  • Available packaging
  • Full description
  • Product parameters

Volume:
1.5 L

Vendor code:
1410112-150
1410112-150-01-999

Code:
4014835755512

Volume:
5 L

Vendor code:
1410112-005
1410112-005-01-999

Code:
4014835755550

Volume:
10 L

Vendor code:
1410112-010
 

Volume:
20 L

Vendor code:
1410112-020
1410112-020-01-999

Code:
4014835755529

Volume:
20 L, ecobox

Vendor code:
1410112-B20
1410112-B20-01-888

Code:
4014835855953

Volume:
60 L, plastic

Vendor code:
1410112-060
1410112-060-01-999

Code:
4014835755567

Volume:
208 L

Vendor code:
1410112-208
1410112-208-01-999

Code:
4014835755581

Volume:
1000 L

Vendor code:
1410112-700
 

The quality of an antifreeze is no longer just determined by the antifreeze effect (which automatically exists in an ethylene-glycol based product), but by the rust protection. That is why manufacturers subject antifreeze to lengthy corrosion and cavitation tests.

RAVENOL OTC Organic Techn. Coolant Premix -40°C protects the cooling system from rust, frost, and in summer, from overheating.

Application instructions

RAVENOL OTC Organic Techn. Coolant Premix -40°C is a prediluted coolant with frost and rust protection for year-round use in automotive engines.

Even in summer coolant must contain enough antifreeze to ensure good corrosion and overheating protection.

Instructions: Add RAVENOL OTC Organic Techn. Coolant Premix -40°C to radiator to fill line.

RAVENOL OTC Organic Techn. Coolant Premix -40°C can also be used as a “ready for use” dilution in geothermal probes and geothermal collectors as recommended list of LAWA (Federal / State Working Group on Water in Germany). 

Characteristics

  • Excellent for light metal engines
  • Good reserve alkalinity
  • Premium corrosion additives for optimal rust protection for all metals and metal alloys used in coolsystems, including aluminium
  • Prevents sediments and foaming in the cooling system
  • Compatible with elastomers used in automotive radiators
  • Can be mixed with other coolant types
Parameter Unit Value Tests
Recomendations DAF 74002, DTFR 29C110 (MB 325.3), DTFR 29D110 (MB 326.3), Deutz DQC CB-14, Ford WSS-M97 B44-D, GM 6277 M, GM B0401065, MAN 324 Type SNF, MB 325.3, MB 326.3, SAE J 1034, VW G 012 A8F, VW TL 774-D, VW TL 774-F, Volvo VCS
DAF 74002, DTFR 29C110 (MB 325.3), DTFR 29D110 (MB 326.3), Deutz DQC CB-14, Ford WSS-M97 B44-D, GM 6277 M, GM B0401065, MAN 324 Type SNF, MB 325.3, MB 326.3, SAE J 1034, VW G 012 A8F, VW TL 774-D, VW TL 774-F, Volvo VCS
Suitable for Jaguar Land Rover STJLR.651.5003, Porsche
Jaguar Land Rover STJLR.651.5003, Porsche
Density at 20 °C g/cm³ 1070 EN ISO 12185
1070 g/cm³ EN ISO 12185
Color Violet visual
Violet visual
pH - value at 20 °C 7,5 - 8,5 ASTM D1287
7,5 - 8,5 ASTM D1287
Freezing point °C -40 ASTM D1177
-40 °C ASTM D1177
Approvals DAF 74002, DTFR 29C110 (MB 325.3), DTFR 29D110 (MB 326.3), Deutz DQC CB-14, Ford WSS-M97 B44-D, GM 6277 M, GM B0401065, MAN 324 Type SNF, MB 325.3, MB 326.3, SAE J 1034, VW G 012 A8F, VW TL 774-D, VW TL 774-F, Volvo VCS
DAF 74002, DTFR 29C110 (MB 325.3), DTFR 29D110 (MB 326.3), Deutz DQC CB-14, Ford WSS-M97 B44-D, GM 6277 M, GM B0401065, MAN 324 Type SNF, MB 325.3, MB 326.3, SAE J 1034, VW G 012 A8F, VW TL 774-D, VW TL 774-F, Volvo VCS
Recommendations DAF 74002, DTFR 29C110 (MB 325.3), DTFR 29D110 (MB 326.3), Deutz DQC CB-14, Ford 1336797, Ford 1336807, Ford 1365305, Ford WSS-M97B44-D (ab Modell 1999), Jaguar JLM 209722, Jaguar Land Rover STJLR.651.5003, Land Rover STC50529, MAN 324 SNF, MB 325.3, MB 326.3 (Premix), Mitsubishi 0103044, Mitsubishi 0103045, Mitsubishi MZ311986, Opel/GM 6277 M, Opel/GM B0401065, Porsche, SAE J1034, Toyota 00272-1LLAC, Toyota 08889-00115, Toyota 08889-01005, Toyota 08889-80014, Toyota 08889-80015, VOLVO VCS (STD 418-0001), VW G 012 A8F M1, VW G 012 A8F M8, VW G 012 A8F M9, VW TL 774-F (entspricht G12+), VW/Audi TL 774-D (entspricht G12+), Volvo 9437650, Volvo 9437651
DAF 74002, DTFR 29C110 (MB 325.3), DTFR 29D110 (MB 326.3), Deutz DQC CB-14, Ford 1336797, Ford 1336807, Ford 1365305, Ford WSS-M97B44-D (ab Modell 1999), Jaguar JLM 209722, Jaguar Land Rover STJLR.651.5003, Land Rover STC50529, MAN 324 SNF, MB 325.3, MB 326.3 (Premix), Mitsubishi 0103044, Mitsubishi 0103045, Mitsubishi MZ311986, Opel/GM 6277 M, Opel/GM B0401065, Porsche, SAE J1034, Toyota 00272-1LLAC, Toyota 08889-00115, Toyota 08889-01005, Toyota 08889-80014, Toyota 08889-80015, VOLVO VCS (STD 418-0001), VW G 012 A8F M1, VW G 012 A8F M8, VW G 012 A8F M9, VW TL 774-F (entspricht G12+), VW/Audi TL 774-D (entspricht G12+), Volvo 9437650, Volvo 9437651
RAVENOL OTC Concentrate Protect C12+

RAVENOL OTC Concentrate Protect C12+

Coolant

RAVENOL OTC Organic Techn. Coolant Concentrate C12+ is an eco-friendly 1.2- Ethanediol (monoethylene glycol) based silicate, borate, nitrite, amine and phosphate-free coolant for cooling circuits in combustion engines which provides maintenance-free corrosion and frost protection. This product is formulated based on a proven inhibitor development with the organic additive technology OAT as an extended life coolant.

Compliance with the requirements:
DAF 74002, DTFR 29C110 (MB 325.3), Deutz DQC CB-14, Ford WSS-M97 B44-D, GM 6277 M, GM B0401065, MAN 324 Type SNF, MB 325.3, SAE J 1034, VW G 012 A8F, VW TL 774-D, VW TL 774-F, Volvo VCS

Show more Hide details
  • Available packaging
  • Full description
  • Product parameters

Volume:
1.5 L

Vendor code:
1410110-150
1410110-150-01-999

Code:
4014835755413

Volume:
5 L

Vendor code:
1410110-005
1410110-005-01-999

Code:
4014835755451

Volume:
10 L

Vendor code:
1410110-010
 

Volume:
20 L

Vendor code:
1410110-020
1410110-020-01-999

Code:
4014835755420

Volume:
20 L, ecobox

Vendor code:
1410110-B20
1410110-B20-01-888

Code:
4014835855212

Volume:
60 L

Vendor code:
1410110-060
1410110-060-01-999

Code:
4014835755468

Volume:
60 L, plastic

Vendor code:

1410110-060-01-995

Code:
4014835755437

Volume:
60 L, print

Vendor code:
1410110-D60
 

Volume:
208 L

Vendor code:
1410110-208
1410110-208-01-999

Code:
4014835755482

Volume:
1000 L

Vendor code:
1410110-700
 

The quality of an antifreeze is no longer just determined by the antifreeze effect (which automatically exists in an ethylene-glycol based product), but by the rust protection. That is why manufacturers subject antifreeze to lengthy corrosion and cavitation tests.

RAVENOL OTC Organic Techn. Coolant Concentrate C12+ protects the cooling system from rust, frost, and in summer, from overheating.

Application instructions

RAVENOL OTC Organic Techn. Coolant Concentrate C12+ with highly effective frost and rust protection. Usable in cooling systems with all-aluminium engines. Mix according to chart. Follow manufacturer's recommendations.

Even in summer coolant must contain enough antifreeze to ensure good corrosion and overheating protection.

Instructions: Clean cooling system, check for leaks, flush.

Mix RAVENOL OTC Organic Techn. Coolant Concentrate C12+ with distilled water (per mixing chart) and add. Allow engine and heater to warm up, add coolant to fill level.

MAN information for use:

Mixing prohibited with Type NF and Type N. Do not use silicone radiator hoses per MAN 334 Type 3 (blue) with coolants per MAN 324 Type SNF.

 

Table of mixing ratios
Antifreeze protection untilParts AntifreezeParts Water
-20°C35%65%
-37°C50%50%
-50°C60%40%

 

Characteristics

  • Excellent for light metal engines
  • Good reserve alkalinity
  • Premium corrosion additives for optimal rust protection for all metals and metal alloys used in cool
  • systems, including aluminium
  • Prevents sediments and foaming in the cooling system
  • Compatible with elastomers used in automotive radiators
  • Can be mixed with other coolant types
Parameter Unit Value Tests
Recomendations DAF 74002, DTFR 29C110 (MB 325.3), Deutz DQC CB-14, Ford WSS-M97 B44-D, GM 6277 M, GM B0401065, MAN 324 Type SNF, MB 325.3, SAE J 1034, VW G 012 A8F, VW TL 774-D, VW TL 774-F, Volvo VCS
DAF 74002, DTFR 29C110 (MB 325.3), Deutz DQC CB-14, Ford WSS-M97 B44-D, GM 6277 M, GM B0401065, MAN 324 Type SNF, MB 325.3, SAE J 1034, VW G 012 A8F, VW TL 774-D, VW TL 774-F, Volvo VCS
Suitable for Jaguar Land Rover STJLR.651.5003, Porsche
Jaguar Land Rover STJLR.651.5003, Porsche
Density at 20 °C g/cm³ 1130 EN ISO 12185
1130 g/cm³ EN ISO 12185
Color Violet visual
Violet visual
Freezing point (50 % solution) °C -37 ASTM D1177
-37 °C ASTM D1177
pH - value at 20 °C (50 Vol %) 7,5 - 8,5 ASTM D1287
7,5 - 8,5 ASTM D1287
Approvals DAF 74002, DTFR 29C110 (MB 325.3), Deutz DQC CB-14, Ford WSS-M97 B44-D, GM 6277 M, GM B0401065, MAN 324 Type SNF, MB 325.3, SAE J 1034, VW G 012 A8F, VW TL 774-D, VW TL 774-F, Volvo VCS
DAF 74002, DTFR 29C110 (MB 325.3), Deutz DQC CB-14, Ford WSS-M97 B44-D, GM 6277 M, GM B0401065, MAN 324 Type SNF, MB 325.3, SAE J 1034, VW G 012 A8F, VW TL 774-D, VW TL 774-F, Volvo VCS
Recommendations DAF 74002, DTFR 29C110 (MB 325.3), Deutz DQC CB-14, Ford 1336797, Ford 1336807, Ford 1365305, Ford WSS-M97B44-D (ab Modell 1999), Jaguar JLM 209722, Jaguar Land Rover STJLR.651.5003, Land Rover STC50529, MAN 324 SNF, MB 325.3, Mitsubishi 0103044, Mitsubishi 0103045, Mitsubishi MZ311986, Opel/GM 6277 M, Opel/GM B0401065, Porsche, SAE J1034, Toyota 00272-1LLAC, Toyota 08889-00115, Toyota 08889-01005, Toyota 08889-80014, Toyota 08889-80015, VOLVO VCS (STD 418-0001), VW G 012 A8F M1, VW G 012 A8F M8, VW G 012 A8F M9, VW TL 774-F (entspricht G12+), VW/Audi TL 774-D (entspricht G12+), Volvo 9437650, Volvo 9437651
DAF 74002, DTFR 29C110 (MB 325.3), Deutz DQC CB-14, Ford 1336797, Ford 1336807, Ford 1365305, Ford WSS-M97B44-D (ab Modell 1999), Jaguar JLM 209722, Jaguar Land Rover STJLR.651.5003, Land Rover STC50529, MAN 324 SNF, MB 325.3, Mitsubishi 0103044, Mitsubishi 0103045, Mitsubishi MZ311986, Opel/GM 6277 M, Opel/GM B0401065, Porsche, SAE J1034, Toyota 00272-1LLAC, Toyota 08889-00115, Toyota 08889-01005, Toyota 08889-80014, Toyota 08889-80015, VOLVO VCS (STD 418-0001), VW G 012 A8F M1, VW G 012 A8F M8, VW G 012 A8F M9, VW TL 774-F (entspricht G12+), VW/Audi TL 774-D (entspricht G12+), Volvo 9437650, Volvo 9437651
RAVENOL destilliertes Wasser

RAVENOL destilliertes Wasser

For batteries

RAVENOL destilliertes Wasser is deionised distilled water and is manufactured using the ion exchangerprocess.

Compliance with the requirements:
DIN 43530-4, DIN EN 50272

Show more Hide details
  • Available packaging
  • Full description
  • Product parameters

Volume:
1 L

Vendor code:
1360010-001
1360010-001-01-000

Code:
4014835300453

Volume:
5 L

Vendor code:
1360010-005
1360010-005-01-000

Code:
4014835300507

Volume:
5 L, specialist. canister

Vendor code:
1360010-005
1360010-005-01-001

Code:
4014835300514

Volume:
208 L

Vendor code:
1360010-208
 

Volume:
1000 L

Vendor code:
1360010-700
 

Volume:
20 L

Vendor code:
1360010-020
1360010-020-01-001

Code:
4014835300422

In the course of this process, the water flows through a column filled with ion exchange resin. This has theability to exchange its accumulated ions for the ions present in the water.

As the ion exchange resin cannot accumulate an infinite number of ions, they have to be “revived”, i.e. theyhave to be regenerated. This takes place using the currently most commonly used regeneration agents: sodiumchloride (water softening), hydrochloric acid (cation exchange) and sodium hydroxide (anion exchange).The conductivity of the water flowing through is constantly checked in a fully automated process and the ionexchanger unit regulates itself automatically.

RAVENOL destilliertes Wasser deionised water is regularly checked by taking samples.

Application instructions

RAVENOL destilliertes Wasser is ideally suited to filling up vehicle batteries and for steam irons and aquariums (to reduce the hardness of the water).

Parameter Unit Value Tests
Recomendations DIN 43530-4, DIN EN 50272
DIN 43530-4, DIN EN 50272
Approvals DIN 43530-4, DIN EN 50272
DIN 43530-4, DIN EN 50272
Recommendations DIN 43 530-4 Akkumulatoren, DIN EN 50272, Elektrolyt und Nachfüllwasser
DIN 43 530-4 Akkumulatoren, DIN EN 50272, Elektrolyt und Nachfüllwasser
RAVENOL Professional Radiator Cleaner

RAVENOL Professional Radiator Cleaner

Additive

RAVENOL Professional Radiator Cleaner is a radiator cleaning additive, which is used for the quick and easy cleaning of the cooling and heating system.

Show more Hide details
  • Available packaging
  • Full description
  • Product parameters

Volume:
0.25 L

Vendor code:
1390302-250
1390302-250-05-000

Code:
4014835802667

RAVENOL Professional Radiator Cleaner breaks down and binds greasy and oily deposits in radiators, heating systems and pipelines.

RAVENOL Professional Radiator Cleaner infiltrates and eliminates sludge and corrosion deposits.RAVENOL Professional Radiator Stop Cleaner neutralises lime residue.

Application instructions

RAVENOL Professional Radiator Cleaner is added to the radiator. It is recommended to replace rubber parts affected by oil seepage.

Area of application:

Radiator repairs

In the event of reduced radiator performance

In the event of deposits in the cooling system

Changing coolant

For cleaning purposes after engine repairs due to oil in the cooling system

Application: RAVENOL Professional Radiator Cleaner suffices for up to 10 litres of coolant.

Fill in

RAVENOL Professional Radiator Cleanerin the used coolant and allow the engine to run at operating temperature for approx. 30 minutes. Drain contaminated mixture – in the case of severe contamination, repeat treatment if necessary. Rinse cooling system with clear water. Refill and remove air after cleaning the cooling system and check for leak tightness.

RAVENOL Professional Radiator Cleaner can lead to an improved cooling performance after repairs on the cooling system.

Characteristics

  • Cleaning of the cooling and heating system
  • Protection of the new coolant against prior contamination
  • Elimination of sludge and corrosion residue
Parameter Unit Value Tests
pH - value at 20 °C 10,25 DIN 19268
10,25 DIN 19268
Density at 20 °C g/cm³ 1003 EN ISO 12185
1003 g/cm³ EN ISO 12185
Color Colorless visual
Colorless visual

Recognizing the number...