Search by VIN, truck make, model, type or unit name, or by the part number of any oil:
Oil for Iveco, EuroCargo Tector (6 --> 10 t) Euro 3 / 4 / 5 (2001-2014), EuroCargo Tector ML 100 E18 Euro 4/5
Iveco Model (EuroCargo Tector (6 --> 10 t) Euro 3 / 4 / 5 (2001-2014)) to find out what kind of oil is used for it
Iveco EuroCargo Tector (6 --> 10 t) Euro 3 / 4 / 5 (2001-2014) EuroCargo Tector ML 100 E18 Euro 4/5from 2008 to 2014 Engine oil, automatic transmission fluid, manual transmission oil, antifreeze, brake fluid, power steering fluid and other fluids.
Power:
Nodes and assemblies
- Engine
- Mechanical gearbox
- Transmission, automatic
- Hydraulic actuation, gearbox
- Differential, rear
- Hydraulic clutch system
- Hydraulic brake system ABS
- Lubrication points oilers, other
- Hydraulic system of throw-back cab
- Central lubrication system grease
- Lubrication points oilers, bearings
- Cooling system
Engine
For engine
RAVENOL Super Performance Truck SAE 5W-30 is a high alloyed USHPD low friction engine oil for commercial vehicles. Because of the use of synthetic basic oils the viscosity area 5W-30 could be realised. Because of the cold viscosity SAE 5W a definite cold start (low cold start corrosion) and a supply of all lubrication areas is guaranteed as quickly as possible at very low outside temperatures. Extreme stress applications are controlled by the high temperature viscosity SAE 30. Minimized friction loss and wear.
Manufacturer Approved:
Renault RXD
Compliance with the requirements:
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, MAN M 3277, MB 228.5, MB 235.28, MTU Type 3, Mack EO-M Plus, Scania LDF-3, Voith Retarder B, Volvo VDS-3
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1122102-001
Volume:
20 L, ecobox
Vendor code:
1122102-B20
Volume:
60 L
Vendor code:
1122102-060
Volume:
1000 L
Vendor code:
1122102-700
Application instructions
RAVENOL Super Performance Truck SAE 5W-30 is a high-performance engine oil for commercial vehicles which can be used the whole year and which is adapted to the new exhaust gas emission rules (also for EURO I, II, III, IV and EURO V engines).
RAVENOL Super Performance Truck SAE 5W-3 is suitable for oil change intervals up to more than 100.000 km according to the manufacturer’s specifications.
Characteristics
- Protection against corrosion
- An excellent oxidation stability
- An excellent high temperature stability
- Excellent detergent and dispersant attributes
- Profitability because of a low fuel consumption
- Long endurance because of a high oxidation stability
- Excellent cold start attributes
- A very good viscosity temperature behaviour
- Low evaporation
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 5W-30 |
5W-30
|
||
| Type | Semi-synthetic |
Semi-synthetic
|
||
| API | CF, CI-4 |
CF, CI-4
|
||
| ACEA | E4, E7 |
E4, E7
|
||
| JASO | DH-1 |
DH-1
|
||
| Manufacturer Approved | Renault RXD |
Renault RXD
|
||
| Recomendations | Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, MAN M 3277, MB 228.5, MB 235.28, MTU Type 3, Mack EO-M Plus, Scania LDF-3, Voith Retarder B, Volvo VDS-3 |
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, MAN M 3277, MB 228.5, MB 235.28, MTU Type 3, Mack EO-M Plus, Scania LDF-3, Voith Retarder B, Volvo VDS-3
|
||
| Suitable for | IVECO |
IVECO
|
||
| Density at 20 °C | g/cm³ | 854 | EN ISO 12185 |
854
g/cm³
EN ISO 12185
|
| Color | tan | visual |
tan
visual
|
|
| Viscosity at 100 °C | mm²/s | 11.5 | DIN 51562-1 |
11.5
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 69.3 | DIN 51562-1 |
69.3
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 161 | DIN ISO 2909 |
161
DIN ISO 2909
|
|
| CCS Viscosity at -30 °C | mPa*s | 6000 | ASTM D5293 |
6000
mPa*s
ASTM D5293
|
| Low Temp. Pumping viscosity (MRV) at -35 °C | mPa*s | 16.200 | ASTM D4684 |
16.200
mPa*s
ASTM D4684
|
| Noack Volatility | % | 10.1 | ASTM D5800 |
10.1
%
ASTM D5800
|
| tbn | mgKOH/g | 13 | ASTM D2896 |
13
mgKOH/g
ASTM D2896
|
| Approvals | Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, MAN M 3277, MB 228.5, MB 235.28, MTU Type 3, Mack EO-M Plus, Renault RXD, Scania LDF-3, Voith Retarder B, Volvo VDS-3 |
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, MAN M 3277, MB 228.5, MB 235.28, MTU Type 3, Mack EO-M Plus, Renault RXD, Scania LDF-3, Voith Retarder B, Volvo VDS-3
|
||
| Recommendations | Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, IVECO, JASO DH-1, MAN M 3277, MB 228.5, MB 235.28, MTU Typ 3, Mack EO-M Plus, Scania LDF-3, VOLVO VDS-3, Voith Retarder B |
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, IVECO, JASO DH-1, MAN M 3277, MB 228.5, MB 235.28, MTU Typ 3, Mack EO-M Plus, Scania LDF-3, VOLVO VDS-3, Voith Retarder B
|
RAVENOL Low Emission Truck SAE 15W-40
For engine
RAVENOL Low Emission Truck SAE 15W-40 is a Heavy Duty engine which fulfils API CJ-4 requirements of 2007 and is formulated with unique low SAPS high performance additives in combination with special selected base oils.
Manufacturer Approved:
Cummins CES 20081, DDC 93K218, Mack EO-O Premium Plus, Renault RLD-3, Tatra TDS 30/12, Volvo VDS-4
Compliance with the requirements:
Caterpillar ECF-2, Caterpillar ECF-3, Chrysler MS-10902, DDC 93K214, DTFR 15C100 (MB 228.31), Ford WSS-M2C 171-E, Japan Ultra-Low PM Emission Diesel, John Deere JDQ-78 X, MAN M 3271-1, MAN M 3477, MAN M 3575, MB 228.31, MTU Type 2.1, U.S. EPA Tier 3 emissions regulation
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1123100-001
Volume:
5 L
Vendor code:
1123100-005
Volume:
10 L
Vendor code:
1123100-010
1123100-010-01-999
Code:
4014835726048
Volume:
20 L
Vendor code:
1123100-020
1123100-020-01-999
Code:
4014835726024
Volume:
20 L, ecobox
Vendor code:
1123100-B20
Volume:
60 L
Vendor code:
1123100-060
1123100-060-01-999
Code:
4014835726062
Volume:
60 L, print
Vendor code:
1123100-D60
Volume:
208 L
Vendor code:
1123100-208
1123100-208-01-999
Code:
4014835726086
Volume:
208 L, print
Vendor code:
1123100-D28
Volume:
1000 L
Vendor code:
1123100-700
RAVENOL Low Emission Truck SAE 15W-40 can be used in new engines and also in older models.
RAVENOL Low Emission Truck SAE 15W-40 reduces friction, wear and fuel consumption.
RAVENOL Low Emission Truck SAE 15W-40 improves performance, reliability and cleanliness of the engines.
RAVENOL Low Emission Truck SAE 15W-40 can be used in diesel and petrol engines and reduces the decision with the oil choice. Lower API specifications API CI-4 PLUS, CI-4, CH-4, CG-4, CF-4 are included in API CJ-4 specification.
Application instructions
RAVENOL Low Emission Truck SAE 15W-40 is suitable for use in EURO 5 engines with exhaust systems and in EURO 3 and EURO 4 engines if required by the engine manufacturer.
RAVENOL Low Emission Truck SAE 15W-40 is suitable for use in trucks with EGR (Exhaust Gas Recirculation) and SCR (Selective Catalytic Reduction) with ULSD (maximum 15 ppm sulphur) and conventional diesel (500 ppm sulphur) from Volvo, Mack, Renault, MAN, Iveco, Daimler, DAF, Caterpillar, Komatsu for DPF (Diesel Particulate Filter) as DPD (Diesel Particulate defuser) by ISUZU, MAZDA, NISSAN and DPR (Diesel Particulate active Reduction) of HINO and TOYOTA.
RAVENOL Low Emission Truck SAE 15W-40 is also suitable for use in Nonroad Diesel Engines and in engines EU Step IIA, IIB, IV and US Tier 3, Tier 4 Interim, Tier 4 Final with Biodiesel.
Characteristics
- Excellent protection of the engine after a cold start and under tougher conditions.
- A fast lubrication and sufficiently thick lubricant film at low temperatures is guaranteed.
- Security against formation of sludge, carbon deposits, varnish and corrosion, even under adverse conditions.
- Prevention of premature DPF (diesel particulate filter)-constipation and reduces the maintenance intervals.
- Neutrality towards sealing materials.
- A very stable and excellent viscosity behaviour.
- An excellent shear stability.
- Good detergent and dispersing properties. Protection from foaming.
- Outstanding wear and corrosion protection (even at long periods), high oxidation stability, maximum engine cleanliness.
- Extended oil change intervals and supports the behaviour at low temperatures
- Reduces deposits on the valves to improve engine protection and support to the engine power and fuel performance.
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 15W-40 |
15W-40
|
||
| Type | Semi-synthetic |
Semi-synthetic
|
||
| API | CJ-4, SM, SN |
CJ-4, SM, SN
|
||
| ACEA | E11, E7, E9 |
E11, E7, E9
|
||
| JASO | DH-2 |
DH-2
|
||
| Manufacturer Approved | Cummins CES 20081, DDC 93K218, Mack EO-O Premium Plus, Renault RLD-3, Tatra TDS 30/12, Volvo VDS-4 |
Cummins CES 20081, DDC 93K218, Mack EO-O Premium Plus, Renault RLD-3, Tatra TDS 30/12, Volvo VDS-4
|
||
| Recomendations | Caterpillar ECF-2, Caterpillar ECF-3, Chrysler MS-10902, DDC 93K214, DTFR 15C100 (MB 228.31), Ford WSS-M2C 171-E, Japan Ultra-Low PM Emission Diesel, John Deere JDQ-78 X, MAN M 3271-1, MAN M 3477, MAN M 3575, MB 228.31, MTU Type 2.1, U.S. EPA Tier 3 emissions regulation |
Caterpillar ECF-2, Caterpillar ECF-3, Chrysler MS-10902, DDC 93K214, DTFR 15C100 (MB 228.31), Ford WSS-M2C 171-E, Japan Ultra-Low PM Emission Diesel, John Deere JDQ-78 X, MAN M 3271-1, MAN M 3477, MAN M 3575, MB 228.31, MTU Type 2.1, U.S. EPA Tier 3 emissions regulation
|
||
| Density at 20 °C | g/cm³ | 862 | EN ISO 12185 |
862
g/cm³
EN ISO 12185
|
| Color | Brown | visual |
Brown
visual
|
|
| Viscosity at 100 °C | mm²/s | 14.5 | DIN 51562-1 |
14.5
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 101.5 | DIN 51562-1 |
101.5
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 148 | DIN ISO 2909 |
148
DIN ISO 2909
|
|
| CCS Viscosity at -20 °C | mPa*s | 4310 | ASTM D5293 |
4310
mPa*s
ASTM D5293
|
| tbn | mgKOH/g | 8.2 | ASTM D2896 |
8.2
mgKOH/g
ASTM D2896
|
| Approvals | Caterpillar ECF-2, Caterpillar ECF-3, Chrysler MS-10902, Cummins CES 20081, DDC 93K214, DDC 93K218, DTFR 15C100 (MB 228.31), Ford WSS-M2C 171-E, Japan Ultra-Low PM Emission Diesel, John Deere JDQ-78 X, MAN M 3271-1, MAN M 3477, MAN M 3575, MB 228.31, MTU Type 2.1, Mack EO-O Premium Plus, Renault RLD-3, Tatra TDS 30/12, U.S. EPA Tier 3 emissions regulation, Volvo VDS-4 |
Caterpillar ECF-2, Caterpillar ECF-3, Chrysler MS-10902, Cummins CES 20081, DDC 93K214, DDC 93K218, DTFR 15C100 (MB 228.31), Ford WSS-M2C 171-E, Japan Ultra-Low PM Emission Diesel, John Deere JDQ-78 X, MAN M 3271-1, MAN M 3477, MAN M 3575, MB 228.31, MTU Type 2.1, Mack EO-O Premium Plus, Renault RLD-3, Tatra TDS 30/12, U.S. EPA Tier 3 emissions regulation, Volvo VDS-4
|
||
| Recommendations | Caterpillar ECF-2, Caterpillar ECF-3, Chrysler MS-10902, DTFR 15C100 (MB 228.31), Detroit Diesel DDC 93K214, EURO IV, EURO V, Ford WSS-M2C171-E, JASO DH-2, Japan Ultra-Low PM Emission Diesel, John Deere JDQ-78X Oxidations Test, MAN M 3271-1, MAN M 3477, MAN M 3575, MB 228.31, MTU Typ 2.1, U.S. EPA Tier 3 emissions regulation |
Caterpillar ECF-2, Caterpillar ECF-3, Chrysler MS-10902, DTFR 15C100 (MB 228.31), Detroit Diesel DDC 93K214, EURO IV, EURO V, Ford WSS-M2C171-E, JASO DH-2, Japan Ultra-Low PM Emission Diesel, John Deere JDQ-78X Oxidations Test, MAN M 3271-1, MAN M 3477, MAN M 3575, MB 228.31, MTU Typ 2.1, U.S. EPA Tier 3 emissions regulation
|
Mechanical gearbox
RAVENOL SSG Spec Synt LKW Getriebeöl SAE 75W-80
For gearbox
RAVENOL SSG Spec Synt LKW Getriebeoel 75W-80 is a synthetic low viscosity transmission oil specifically for highly stressed manual transmissions.
Manufacturer Approved:
MAN 341 Type Z4, ZF TE-ML 01L, ZF TE-ML 02L, ZF TE-ML 16K
Compliance with the requirements:
DTFR 13D120 (MB 235.29), Eaton Extended drain, MAN 341 Type E3, MAN 341 Type VR, MAN 341 Type Z5, Voith Type C, Volvo 97305, Volvo 97307, ZF TE-ML 01E, ZF TE-ML 02E, ZF TE-ML 16P
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1221100-001
Volume:
4 L
Vendor code:
1221100-004
Volume:
60 L, print
Vendor code:
1221100-D60
Volume:
1000 L
Vendor code:
1221100-700
RAVENOL SSG Spec Synt LKW Getriebeoel 75W-80 is designed based on synthetic base oils and specially coordinated additive treatment. This exceeds the needs of today's application requirements.
RAVENOL SSG Spec Synt LKW Getriebeoel 75W-80 is outstanding for use under severe mechanical and thermal stress on transmission oils, even with extended oil change intervals.
Application instructions
RAVENOL SSG Spec Synt LKW Getriebeoel 75W-80 is a heavy duty transmission oil to care for synchronised manual transmissions in commercial vehicles with intarder or retarder. Shift comfort isnoticeably increased. Extreme oil change intervals according as specified by the manufacturer at up to 500,000 km reduce maintenance costs and increase cost-effectiveness.
Characteristics
- Excellent thermal stability
- High protection from rust, corrosion, foaming
- Low solidification point
- Excellent EP properties
- Good shifting behaviour in low temperatures
- Extended life
- Fuel savings
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 75W-80 |
75W-80
|
||
| Type | Synthetic |
Synthetic
|
||
| API | GL-4 |
GL-4
|
||
| Manufacturer Approved | MAN 341 Type Z4, ZF TE-ML 01L, ZF TE-ML 02L, ZF TE-ML 16K |
MAN 341 Type Z4, ZF TE-ML 01L, ZF TE-ML 02L, ZF TE-ML 16K
|
||
| Recomendations | DTFR 13D120 (MB 235.29), Eaton Extended drain, MAN 341 Type E3, MAN 341 Type VR, MAN 341 Type Z5, Voith Type C, Volvo 97305, Volvo 97307, ZF TE-ML 01E, ZF TE-ML 02E, ZF TE-ML 16P |
DTFR 13D120 (MB 235.29), Eaton Extended drain, MAN 341 Type E3, MAN 341 Type VR, MAN 341 Type Z5, Voith Type C, Volvo 97305, Volvo 97307, ZF TE-ML 01E, ZF TE-ML 02E, ZF TE-ML 16P
|
||
| specification | MIL-L-2105 |
MIL-L-2105
|
||
| Suitable for | IVECO, Renault |
IVECO, Renault
|
||
| Density at 20 °C | g/cm³ | 855 | EN ISO 12185 |
855
g/cm³
EN ISO 12185
|
| Color | Red | visual |
Red
visual
|
|
| Viscosity at 100 °C | mm²/s | 9.29 | DIN 51562-1 |
9.29
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 51.97 | DIN 51562-1 |
51.97
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 163 | DIN ISO 2909 |
163
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 38.800 | ASTM D2983 |
38.800
mPa*s
ASTM D2983
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | DTFR 13D120 (MB 235.29), Eaton Extended drain, MAN 341 Type E3, MAN 341 Type VR, MAN 341 Type Z4, MAN 341 Type Z5, MIL-L-2105, Voith Type C, Volvo 97305, Volvo 97307, ZF TE-ML 01E, ZF TE-ML 01L, ZF TE-ML 02E, ZF TE-ML 02L, ZF TE-ML 16K, ZF TE-ML 16P |
DTFR 13D120 (MB 235.29), Eaton Extended drain, MAN 341 Type E3, MAN 341 Type VR, MAN 341 Type Z4, MAN 341 Type Z5, MIL-L-2105, Voith Type C, Volvo 97305, Volvo 97307, ZF TE-ML 01E, ZF TE-ML 01L, ZF TE-ML 02E, ZF TE-ML 02L, ZF TE-ML 16K, ZF TE-ML 16P
|
||
| Recommendations | DAF/VOLVO 97305, DAF/VOLVO 97307, DTFR 13D120 (MB 235.29), Eaton (Extended drain), IVECO, MAN 341 E3, MAN 341 VR, MAN 341 Z5, Renault, VOLVO 97317, Voith Typ C, ZF TE-ML 01E, ZF TE-ML 02E, ZF TE-ML 16P |
DAF/VOLVO 97305, DAF/VOLVO 97307, DTFR 13D120 (MB 235.29), Eaton (Extended drain), IVECO, MAN 341 E3, MAN 341 VR, MAN 341 Z5, Renault, VOLVO 97317, Voith Typ C, ZF TE-ML 01E, ZF TE-ML 02E, ZF TE-ML 16P
|
Transmission, automatic
RAVENOL LKW ATF Synthetik
Hydraulic fluid
RAVENOL LKW ATF Synthetik is a synthetic automatic transmission oil developed specifically for the latest generation of commercial vehicle automatic transmissions.
Compliance with the requirements:
Allison TES-295, Allison TES-468, Caterpillar 6-speed CX31, Caterpillar 8-speed Super-Heavy-Duty CX35, DTFR 13C180 (MB 236.91), MAN 339 Type Z4, MB 236.91, Renk Doromat, Voith H55.63353x (G607), Voith H55.63363x (G1363), ZF TE-ML 14E, ZF TE-ML 16N
- Available packaging
- Product parameters
Volume:
4 L
Vendor code:
1211104-004
Volume:
10 L
Vendor code:
1211104-010
1211104-010-01-999
Code:
4014835736849
Volume:
20 L
Vendor code:
1211104-020
1211104-020-01-999
Code:
4014835736825
Volume:
20 L, ecobox
Vendor code:
1211104-B20
Volume:
60 L
Vendor code:
1211104-060
Volume:
60 L, print
Vendor code:
1211104-D60
Volume:
208 L
Vendor code:
1211104-208
1211104-208-01-999
Code:
4014835736887
Volume:
208 L, print
Vendor code:
1211104-D28
1211104-D28-01-888
Code:
4014835736801
Volume:
1000 L
Vendor code:
1211104-700
RAVENOL LKW ATF Synthetik allows oil change intervals to be extended even under severe operating conditions. A new type of additive technology allowed ultimate performance to be achieved with respect to ideal and constant friction characteristics, excellent shearing stability, and fluidity at low temperatures, steady wear protection and outstanding oxidation stability.
Application instructions
RAVENOL LKW ATF Synthetik was developed for use in automatic transmissions in motor vehicles as well as torque converter and power-shift transmissions with the indicated specifications.
Characteristics
- reliable protection from wear, sludge, adhesion and corrosion
- excellent, highly shearing stable viscosity-temperature properties
- no problems in very low and very high temperatures
- a thermally extremely high load capacity
- non-foaming even in extreme conditions
- neutral behavior towards sealing materials
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| Type | Synthetic |
Synthetic
|
||
| Recomendations | Allison TES-295, Allison TES-468, Caterpillar 6-speed CX31, Caterpillar 8-speed Super-Heavy-Duty CX35, DTFR 13C180 (MB 236.91), MAN 339 Type Z4, MB 236.91, Renk Doromat, Voith H55.63353x (G607), Voith H55.63363x (G1363), ZF TE-ML 14E, ZF TE-ML 16N |
Allison TES-295, Allison TES-468, Caterpillar 6-speed CX31, Caterpillar 8-speed Super-Heavy-Duty CX35, DTFR 13C180 (MB 236.91), MAN 339 Type Z4, MB 236.91, Renk Doromat, Voith H55.63353x (G607), Voith H55.63363x (G1363), ZF TE-ML 14E, ZF TE-ML 16N
|
||
| Density at 20 °C | g/cm³ | 834 | EN ISO 12185 |
834
g/cm³
EN ISO 12185
|
| Color | Red | visual |
Red
visual
|
|
| Viscosity at 100 °C | mm²/s | 7.5 | DIN 51562-1 |
7.5
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 32 | DIN 51562-1 |
32
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 191 | DIN ISO 2909 |
191
DIN ISO 2909
|
|
| Approvals | Allison TES-295, Allison TES-468, Caterpillar 6-speed CX31, Caterpillar 8-speed Super-Heavy-Duty CX35, DTFR 13C180 (MB 236.91), MAN 339 Type Z4, MB 236.91, Renk Doromat, Voith H55.63353x (G607), Voith H55.63363x (G1363), ZF TE-ML 14E, ZF TE-ML 16N |
Allison TES-295, Allison TES-468, Caterpillar 6-speed CX31, Caterpillar 8-speed Super-Heavy-Duty CX35, DTFR 13C180 (MB 236.91), MAN 339 Type Z4, MB 236.91, Renk Doromat, Voith H55.63353x (G607), Voith H55.63363x (G1363), ZF TE-ML 14E, ZF TE-ML 16N
|
||
| Recommendations | Allison TES-295, Allison TES-468, Caterpillar 6-speed CX31, Caterpillar 8-speed Super-Heavy-Duty CX35, DTFR 13C180 (MB 236.91), MAN 339 Z4, MB 236.91, Renk Doromat, Voith H55.63353x (G607), Voith H55.63363x (G1363), ZF TE-ML 14E, ZF TE-ML 16N |
Allison TES-295, Allison TES-468, Caterpillar 6-speed CX31, Caterpillar 8-speed Super-Heavy-Duty CX35, DTFR 13C180 (MB 236.91), MAN 339 Z4, MB 236.91, Renk Doromat, Voith H55.63353x (G607), Voith H55.63363x (G1363), ZF TE-ML 14E, ZF TE-ML 16N
|
Hydraulic actuation, gearbox
RAVENOL Elektro-Hydraulik E-PSF Fluid
For power steering
RAVENOL E- PSF Fluid is a specific full synthetic fluid for electro-hydraulic power steering.
Compliance with the requirements:
Fiat 9.55550-AG3, JTEKT EHPS, JTEKT EHS, MAN M3289, Nissan E-PSF, PSA S71 2710, Renault PSF Class 1, Toyota PSF-EH
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1181002-001
1181002-001-01-999
Code:
4014835839908
RAVENOL E- PSF Fluid is guaranteeing an optimized power transmission.
RAVENOL E- PSF Fluid is designed on the basis of particularly high quality base oils with special additives and inhibition which ensures the proper functioning of the electro-hydraulic power steering system.
Application instructions
RAVENOL E- PSF Fluid is especially developed for the use in electro-hydraulic power steering systems of Nissan and Toyota (JTEKT EHS Elektro-Hydraulik Servolenkung/EHPS Electro-Hydraulic Power Steering).
RAVENOL E- PSF Fluid is also suitable for the hydropneumatic Hydractive III und Hydractive III+ suspension of Citroën.
Characteristics
- A very low pour point
- An excellent foam prevention, no foam formation
- A good lubricating ability even at low temperatures in winter
- A high and stable viscosity index
- A very good oxidation stability
- Excellent protection against wear and tear, corrosion and foam formation
- Well-tuned friction characteristics
- Neutral behaviour against sealing materials
- Neutral behaviour because of inhibition against non-ferrous metals
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| Type | Full synthetic |
Full synthetic
|
||
| Recomendations | Fiat 9.55550-AG3, JTEKT EHPS, JTEKT EHS, MAN M3289, Nissan E-PSF, PSA S71 2710, Renault PSF Class 1, Toyota PSF-EH |
Fiat 9.55550-AG3, JTEKT EHPS, JTEKT EHS, MAN M3289, Nissan E-PSF, PSA S71 2710, Renault PSF Class 1, Toyota PSF-EH
|
||
| Suitable for | PSA DA, PSA LSD |
PSA DA, PSA LSD
|
||
| Density at 20 °C | g/cm³ | 821 | EN ISO 12185 |
821
g/cm³
EN ISO 12185
|
| Color | Colorless | visual |
Colorless
visual
|
|
| Viscosity at 100 °C | mm²/s | 6.1 | DIN 51562-1 |
6.1
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 19 | DIN 51562-1 |
19
mm²/s
DIN 51562-1
|
| Viscosity at -40 °C | mm²/s | 960 | ASTM D445 |
960
mm²/s
ASTM D445
|
| Viscosity Index VI | 312 | DIN ISO 2909 |
312
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 900 | ASTM D2983 |
900
mPa*s
ASTM D2983
|
| Approvals | Fiat 9.55550-AG3, JTEKT EHPS, JTEKT EHS, MAN M 3289, Nissan E-PSF, PSA S71 2710, Renault PSF Class 1, Toyota PSF-EH |
Fiat 9.55550-AG3, JTEKT EHPS, JTEKT EHS, MAN M 3289, Nissan E-PSF, PSA S71 2710, Renault PSF Class 1, Toyota PSF-EH
|
||
| Recommendations | Citroën DA 9730 A5, Citroën LDS 9979 A3, Fiat 9.55550-AG3, JTEKT EHS/ EHPS, MAN M 3289, Nissan 999MP-EPSF00P, Nissan E-PSF, Nissan KLF51-00001, PSA S71 2710, Renault PSF Klasse 1 (Renault Laguna III), Toyota 08886-01206, Toyota PSF-EH |
Citroën DA 9730 A5, Citroën LDS 9979 A3, Fiat 9.55550-AG3, JTEKT EHS/ EHPS, MAN M 3289, Nissan 999MP-EPSF00P, Nissan E-PSF, Nissan KLF51-00001, PSA S71 2710, Renault PSF Klasse 1 (Renault Laguna III), Toyota 08886-01206, Toyota PSF-EH
|
Differential, rear
RAVENOL Getriebeoel TGO SAE 75W-90 API GL 5
For gearbox
RAVENOL Transmission Oil TGO SAE 75W-90 API GL 5 is a semi-synthetic transmission oil specifically for maximum duty hypoid geared transmissions.
Compliance with the requirements:
CS 3000B, DTFR 12B100 (MB 235.0), DTFR 12B140 (MB 235.8), DTFR 13B100 (MB 235.1), Ford SQ-M2C 9002-A, MAN 342 Type M2, MB 235.0, MB 235.1, MB 235.14, MB 235.8, MB 235.9, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 07A, ZF TE-ML 16B, ZF TE-ML 16C, ZF TE-ML 16D, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1222105-001
1222105-001-01-999
Code:
4014835734418
Volume:
4 L
Vendor code:
1222105-004
1222105-004-01-999
Code:
4014835734494
Volume:
10 L
Vendor code:
1222105-010
1222105-010-01-999
Code:
4014835734449
Volume:
20 L
Vendor code:
1222105-020
1222105-020-01-999
Code:
4014835734425
Volume:
20 L, ecobox
Vendor code:
1222105-B20
1222105-B20-01-888
Code:
4014835789128
Volume:
60 L
Vendor code:
1222105-060
Volume:
60 L, print
Vendor code:
1222105-D60
1222105-D60-01-888
Code:
4014835734432
Volume:
208 L
Vendor code:
1222105-208
1222105-208-01-999
Code:
4014835734487
Volume:
208 L, print
Vendor code:
1222105-D28
1222105-D28-01-888
Code:
4014835734401
Volume:
1000 L
Vendor code:
1222105-700
RAVENOL Transmission Oil TGO SAE 75W-90 API GL 5 is designed based on high-quality solvent refined and synthetic base oils and specially harmonised additive treatment with extreme pressure (EP) active ingredients and other additives. This exceeds the needs of today's application requirements.
Application instructions
RAVENOL Transmission Oil TGO SAE 75W-90 API GL 5 is a maximum duty transmission oil for use in maximum duty, hypoid geared transmissions (axle drives, manual transmissions, etc.), where maximum duty transmission oils are required.
Characteristics
- Excellent oxidation stability
- Greatest possible protection from rust, corrosion, foaming
- Low solidification point
- Excellent extreme pressure (EP) properties
- High viscosity index
- Fuel savings
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 75W-90 |
75W-90
|
||
| Type | Semi-synthetic |
Semi-synthetic
|
||
| API | GL-5 |
GL-5
|
||
| Recomendations | CS 3000B, DTFR 12B100 (MB 235.0), DTFR 12B140 (MB 235.8), DTFR 13B100 (MB 235.1), Ford SQ-M2C 9002-A, MAN 342 Type M2, MB 235.0, MB 235.1, MB 235.14, MB 235.8, MB 235.9, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 07A, ZF TE-ML 16B, ZF TE-ML 16C, ZF TE-ML 16D, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A |
CS 3000B, DTFR 12B100 (MB 235.0), DTFR 12B140 (MB 235.8), DTFR 13B100 (MB 235.1), Ford SQ-M2C 9002-A, MAN 342 Type M2, MB 235.0, MB 235.1, MB 235.14, MB 235.8, MB 235.9, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 07A, ZF TE-ML 16B, ZF TE-ML 16C, ZF TE-ML 16D, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A
|
||
| specification | MIL-L-2105 D |
MIL-L-2105 D
|
||
| Suitable for | GM |
GM
|
||
| Density at 20 °C | g/cm³ | 842 | EN ISO 12185 |
842
g/cm³
EN ISO 12185
|
| Color | Yellow | visual |
Yellow
visual
|
|
| Viscosity at 100 °C | mm²/s | 15.7 | DIN 51562-1 |
15.7
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 97.3 | DIN 51562-1 |
97.3
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 173 | DIN ISO 2909 |
173
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 70.000 | ASTM D2983 |
70.000
mPa*s
ASTM D2983
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | CS 3000B, DTFR 12B100 (MB 235.0), DTFR 12B140 (MB 235.8), DTFR 13B100 (MB 235.1), Ford SQ-M2C 9002-A, MAN 342 Type M2, MB 235.0, MB 235.1, MB 235.14, MB 235.8, MB 235.9, MIL-L-2105 D, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 07A, ZF TE-ML 16B, ZF TE-ML 16C, ZF TE-ML 16D, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A |
CS 3000B, DTFR 12B100 (MB 235.0), DTFR 12B140 (MB 235.8), DTFR 13B100 (MB 235.1), Ford SQ-M2C 9002-A, MAN 342 Type M2, MB 235.0, MB 235.1, MB 235.14, MB 235.8, MB 235.9, MIL-L-2105 D, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 07A, ZF TE-ML 16B, ZF TE-ML 16C, ZF TE-ML 16D, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A
|
||
| Recommendations | CS 3000B, DTFR 12B100 (MB 235.0), DTFR 12B140 (MB 235.8), DTFR 13B100 (MB 235.1), Ford M2C-9002A, GM, MAN 342 M2 (160.000 km), MB 235.0, MB 235.1, MB 235.14, MB 235.8, MB 235.9, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 07A, ZF TE-ML 16B, ZF TE-ML 16C, ZF TE-ML 16D, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A |
CS 3000B, DTFR 12B100 (MB 235.0), DTFR 12B140 (MB 235.8), DTFR 13B100 (MB 235.1), Ford M2C-9002A, GM, MAN 342 M2 (160.000 km), MB 235.0, MB 235.1, MB 235.14, MB 235.8, MB 235.9, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 07A, ZF TE-ML 16B, ZF TE-ML 16C, ZF TE-ML 16D, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A
|
For transmission
RAVENOL VSG SAE 75W-90 is a high performance universal transmission oil based on full synthetic components.
Compliance with the requirements:
BMW MTF-LT-4, BMW OSP, BMW SAF-XO, BOT 130 M, BOT 328, BOT 720, DAF LKW, DTFR 12B140 (MB 235.8), DTFR 13B110 (MB 235.11), Ford WSD-M2C 200-C, MAN 342 Type S1, MB 235.11, MB 235.21, MB 235.72, MB 235.8, MB 235.9, MIL-L-2105 D, Renault LKW, Scania STO 1:0, VW G 052 145, VW G 052 539, VW G 052 580, VW G 052 911, VW G 060 517 A2, ZF TE-ML 12B, ZF TE-ML 16F, ZF TE-ML 17B
- Available packaging
- Product parameters
Volume:
1000 L
Vendor code:
1221101-700
RAVENOL VSG SAE 75W-90 is designed based on high-quality synthetic base oils with a special additive treatment and inhibition ensuring trouble-free transmission function.
Application instructions
RAVENOL VSG SAE 75W-90 is excellent for use of highly stressed axle drives.
RAVENOL VSG SAE 75W-90 is suitable for synchronised and non-synchronised manual transmissions, transfer cases and ancillary transmission requiring API GL-5 or GL-4 oil.
RAVENOL VSG SAE 75W-90 is suitable for Ford-transmission IB5, B5, MTX75, GM5, MT285/6, MMT6/6, MT75, R15M-D, R15MX-D, MT82 and Porsche Full-Time Transfer Case with Torsen (PL72T) for Cayenne 92A / 958 Diesel and S Hybrid from 2010 to 2018.
Characteristics
- high additive reserves for prolonged oil change intervals according to the manufacturer specifications
- excellent cold flow properties
- best wear protection and best transmission efficiency
- Fuel savings even with short distances in low outdoor temperatures
- stable lubricating film even under high stress
- extraordinary corrosion protection and good compatibility with non-ferrous metal
- high oxidation resistance prevents oil thickening and deposits
- outstanding dirt-carrying capacity, i.e. aggregates are clean even after very long oil change intervals
- excellent elastomer compatibility to prevent leaks
- extreme shearing stability, remains within the clean oil viscosity per SAE class 75W-90 even after very long periods of use
- very high protection from rust, corrosion and foaming
- extreme low pour point
- excellent EP properties
- fuel savings
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 75W-90 |
75W-90
|
||
| Type | Full synthetic |
Full synthetic
|
||
| API | GL-4, GL-5 |
GL-4, GL-5
|
||
| Recomendations | BMW MTF-LT-4, BMW OSP, BMW SAF-XO, BOT 130 M, BOT 328, BOT 720, DAF LKW, DTFR 12B140 (MB 235.8), DTFR 13B110 (MB 235.11), Ford WSD-M2C 200-C, MAN 342 Type S1, MB 235.11, MB 235.21, MB 235.72, MB 235.8, MB 235.9, MIL-L-2105 D, Renault LKW, Scania STO 1:0, VW G 052 145, VW G 052 539, VW G 052 580, VW G 052 911, VW G 060 517 A2, ZF TE-ML 12B, ZF TE-ML 16F, ZF TE-ML 17B |
BMW MTF-LT-4, BMW OSP, BMW SAF-XO, BOT 130 M, BOT 328, BOT 720, DAF LKW, DTFR 12B140 (MB 235.8), DTFR 13B110 (MB 235.11), Ford WSD-M2C 200-C, MAN 342 Type S1, MB 235.11, MB 235.21, MB 235.72, MB 235.8, MB 235.9, MIL-L-2105 D, Renault LKW, Scania STO 1:0, VW G 052 145, VW G 052 539, VW G 052 580, VW G 052 911, VW G 060 517 A2, ZF TE-ML 12B, ZF TE-ML 16F, ZF TE-ML 17B
|
||
| Suitable for | IVECO |
IVECO
|
||
| Density at 20 °C | g/cm³ | 839.8 | EN ISO 12185 |
839.8
g/cm³
EN ISO 12185
|
| Color | Yellow | visual |
Yellow
visual
|
|
| Viscosity at 100 °C | mm²/s | 16.8 | DIN 51562-1 |
16.8
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 108.8 | DIN 51562-1 |
108.8
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 168 | DIN ISO 2909 |
168
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 47.000 | ASTM D2983 |
47.000
mPa*s
ASTM D2983
|
| Seq. I at 24 °C | ml/ml | 0/0 | ASTM D892 |
0/0
ml/ml
ASTM D892
|
| Seq. II at 93,5 °C | ml/ml | 0/0 | ASTM D892 |
0/0
ml/ml
ASTM D892
|
| Seq. III at 24 °C after 93,5 °C | ml/ml | 0/0 | ASTM D892 |
0/0
ml/ml
ASTM D892
|
| Copper Strip Test at 121 °C | 1a | ASTM D130 |
1a
ASTM D130
|
|
| Approvals | BMW MTF-LT-4, BMW OSP, BMW SAF-XO, BOT 130 M, BOT 328, BOT 720, DAF LKW, DTFR 12B140 (MB 235.8), DTFR 13B110 (MB 235.11), Ford WSD-M2C 200-C, MAN 342 Type S1, MB 235.11, MB 235.21, MB 235.72, MB 235.8, MB 235.9, MIL-L-2105 D, Renault LKW, Scania STO 1:0, VW G 052 145, VW G 052 539, VW G 052 580, VW G 052 911, VW G 060 517 A2, ZF TE-ML 12B, ZF TE-ML 16F, ZF TE-ML 17B |
BMW MTF-LT-4, BMW OSP, BMW SAF-XO, BOT 130 M, BOT 328, BOT 720, DAF LKW, DTFR 12B140 (MB 235.8), DTFR 13B110 (MB 235.11), Ford WSD-M2C 200-C, MAN 342 Type S1, MB 235.11, MB 235.21, MB 235.72, MB 235.8, MB 235.9, MIL-L-2105 D, Renault LKW, Scania STO 1:0, VW G 052 145, VW G 052 539, VW G 052 580, VW G 052 911, VW G 060 517 A2, ZF TE-ML 12B, ZF TE-ML 16F, ZF TE-ML 17B
|
||
| Recommendations | BMW 83222339223 MTF-LT-4, BMW 83222365987, BMW 83229407768, BMW OSP, BMW SAF-XO, BOT 130 M, BOT 328, BOT 720, DAF LKW (für verlängerte Intervalle), DTFR 12B140 (MB 235.8), DTFR 13B110 (MB 235.11), Ford 1045737, Ford 5021033, Ford MU7J 19G518 AA, Ford WSD-M2C200-C, IVECO, Land Rover TYK500010, MAN 342 S1, MB 235.11, MB 235.21, MB 235.72, MB 235.8, MB 235.9, MIL-L-2105 D, Porsche 000.043.305.04, Porsche 958.341.536.00 (Torsen 2010-2018), Renault LKW, Scania STO 1:0, VOLVO 97312, VOLVO 97315, VOLVO 97319, VW G 052 145 A2, VW G 052 539 A2, VW G 052 580, VW G 052 911 A2, VW G 060 517 A2, ZF TE-ML 12B, ZF TE-ML 16F, ZF TE-ML 17B |
BMW 83222339223 MTF-LT-4, BMW 83222365987, BMW 83229407768, BMW OSP, BMW SAF-XO, BOT 130 M, BOT 328, BOT 720, DAF LKW (für verlängerte Intervalle), DTFR 12B140 (MB 235.8), DTFR 13B110 (MB 235.11), Ford 1045737, Ford 5021033, Ford MU7J 19G518 AA, Ford WSD-M2C200-C, IVECO, Land Rover TYK500010, MAN 342 S1, MB 235.11, MB 235.21, MB 235.72, MB 235.8, MB 235.9, MIL-L-2105 D, Porsche 000.043.305.04, Porsche 958.341.536.00 (Torsen 2010-2018), Renault LKW, Scania STO 1:0, VOLVO 97312, VOLVO 97315, VOLVO 97319, VW G 052 145 A2, VW G 052 539 A2, VW G 052 580, VW G 052 911 A2, VW G 060 517 A2, ZF TE-ML 12B, ZF TE-ML 16F, ZF TE-ML 17B
|
For differentials
RAVENOL Getriebeoel LS SAE 75W-90 is a synthetic lubricant for mechanical transmissions.
Compliance with the requirements:
ZF TE-ML 05C, ZF TE-ML 05D
- Available packaging
- Product parameters
Volume:
20 L
Vendor code:
1222102-020
Volume:
208 L
Vendor code:
1222102-208
Volume:
1000 L
Vendor code:
1222102-700
Volume:
60 L
Vendor code:
1222102-060
1222102-060-01-999
Code:
4014835734364
RAVENOL Getriebeoel LS SAE 75W-90 is designed based on high-quality solvent refined and synthetic base oils with special additive treatment and inhibition for higher stress on manual transmission oils and ensuring trouble-free transmission function.
Application instructions
RAVENOL Getriebeoel LS SAE 75W-90 was developed specifically for use in differential gear units with limited slip. It also ensures trouble-free lubrication in self-locking, hypoid geared transmissions.
Characteristics
- excellent oxidation stability
- excellent protection against rust and corrosion
- prevents foaming
- outstanding extreme pressure properties
- excellent limited slip properties
- fuel savings
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 75W-90 |
75W-90
|
||
| Type | Synthetic |
Synthetic
|
||
| API | GL-5 LS |
GL-5 LS
|
||
| Recomendations | ZF TE-ML 05C, ZF TE-ML 05D |
ZF TE-ML 05C, ZF TE-ML 05D
|
||
| specification | MIL-L-2105 D |
MIL-L-2105 D
|
||
| Density at 20 °C | g/cm³ | 839 | EN ISO 12185 |
839
g/cm³
EN ISO 12185
|
| Color | Yellow | visual |
Yellow
visual
|
|
| Viscosity at 100 °C | mm²/s | 17.1 | DIN 51562-1 |
17.1
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 102.1 | DIN 51562-1 |
102.1
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 182 | DIN ISO 2909 |
182
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 84.300 | ASTM D2983 |
84.300
mPa*s
ASTM D2983
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D |
MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D
|
||
| Recommendations | GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D |
GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D
|
For transmission
In order to avoid the seasonal change of the transmission oil RAVENOL Getriebeoel EPX SAE 80W-90 GL-5 was developed. It can be used in winter as well as in summer. Its universal use reduces the risk of mix-up and storage.
Manufacturer Approved:
LOVAT LOV-204, ZF TE-ML 16B, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A
Compliance with the requirements:
DTFR 12B100 (MB 235.0), Ford SQ-M2C 9002-AA, MAN 342 Type M1, MB 235.0, MIL-L-2105 D
- Available packaging
- Product parameters
Volume:
208 L, print
Vendor code:
1223205-D28
Volume:
1000 L
Vendor code:
1223205-700
RAVENOL Getriebeoel EPX SAE 80W-90 GL-5 guarantees due to the balanced additive combination characteristics like a high pressure absorption capacity, a superior viscosity temperature behaviour, a high oxidation stability, low pour points, a good corrosion protection and non-sludging.
Application instructions
RAVENOL Getriebeoel EPX SAE 80W-90 GL-5 is compatible with all brand-name transmission oils. No “flushing” required when switching to RAVENOL Getriebeoel EPX SAE 80W-90 GL-5.
Use RAVENOL Getriebeoel EPX SAE 80W-90 GL-5 in hypoid gears for hypoid gearbox, manual transmissions, axle drives, distributor and intermediate transmissions in vehicles and working machines.
Characteristics
- Optimal cold flow property
- Outstanding wear protection even with short trips in winter
- High pressure stable lubrication film, thus outstanding wear protection under any stress
- Reduced transmission noise and the best transmission efficiency under full load, i.e. even with very hot oil
- Outstanding shearing stability
- Excellent oxidation stability, no foaming
- No oil thickening or deposits
- Extraordinary ageing stability
- Excellent viscosity-temperature properties
- Effective wear protection
- Extraordinary corrosion protection, no rust, won’t harm non-ferrous metals
- Neutral to sealants, transmissions stay tight, no oil loss
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 80W-90 |
80W-90
|
||
| Type | Mineral |
Mineral
|
||
| API | GL-5 |
GL-5
|
||
| Manufacturer Approved | LOVAT LOV-204, ZF TE-ML 16B, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A |
LOVAT LOV-204, ZF TE-ML 16B, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A
|
||
| Recomendations | DTFR 12B100 (MB 235.0), Ford SQ-M2C 9002-AA, MAN 342 Type M1, MB 235.0, MIL-L-2105 D |
DTFR 12B100 (MB 235.0), Ford SQ-M2C 9002-AA, MAN 342 Type M1, MB 235.0, MIL-L-2105 D
|
||
| Density at 20 °C | g/cm³ | 882 | EN ISO 12185 |
882
g/cm³
EN ISO 12185
|
| Color | tan | visual |
tan
visual
|
|
| Viscosity at 100 °C | mm²/s | 14.3 | DIN 51562-1 |
14.3
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 130.3 | DIN 51562-1 |
130.3
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 108 | DIN ISO 2909 |
108
DIN ISO 2909
|
|
| Brookfield Viscosity at -26 °C | mPa*s | 60.100 | ASTM D2983 |
60.100
mPa*s
ASTM D2983
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | DTFR 12B100 (MB 235.0), Ford SQ-M2C 9002-AA, LOVAT LOV-204, MAN 342 Type M1, MB 235.0, MIL-L-2105 D, ZF TE-ML 16B, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A |
DTFR 12B100 (MB 235.0), Ford SQ-M2C 9002-AA, LOVAT LOV-204, MAN 342 Type M1, MB 235.0, MIL-L-2105 D, ZF TE-ML 16B, ZF TE-ML 17B, ZF TE-ML 19B, ZF TE-ML 21A
|
||
| Recommendations | DTFR 12B100 (MB 235.0), Ford SQM-2C-9002 AA, MAN 342 M1, MB 235.0, MIL-L-2105 D |
DTFR 12B100 (MB 235.0), Ford SQM-2C-9002 AA, MAN 342 M1, MB 235.0, MIL-L-2105 D
|
RAVENOL Getriebeoel EPX SAE 85W-140 GL-5
For transmission
RAVENOL Getriebeoel EPX SAE 85W-140 GL-5 is a lubricating oil for mechanical gears based on high quality and solvent refined base oils. Special extreme pressure (EP)-active substances and selected additives give excellent lubricating oil properties.
Compliance with the requirements:
CS 3000B, Ford SQ-M2C 9002-A, MAN 342 Type M1, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 16D, ZF TE-ML 21A
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1223211-001
Volume:
4 L
Vendor code:
1223211-004
1223211-004-01-999
Code:
4014835738393
Volume:
10 L
Vendor code:
1223211-010
1223211-010-01-999
Code:
4014835738348
Volume:
20 L
Vendor code:
1223211-020
1223211-020-01-999
Code:
4014835738324
Volume:
20 L, ecobox
Vendor code:
1223211-B20
Volume:
60 L
Vendor code:
1223211-060
1223211-060-01-999
Code:
4014835738362
Volume:
208 L
Vendor code:
1223211-208
1223211-208-01-999
Code:
4014835738386
Volume:
208 L, print
Vendor code:
1223211-D28
Volume:
1000 L
Vendor code:
1223211-700
RAVENOL Getriebeoel EPX SAE 85W-140 GL-5 is designed for use with maximum duty, hypoid gearing gears (axel drive, manual transmission, etc.), so far extreme pressure gear oils are required.
Application instructions
RAVENOL Getriebeoel EPX SAE 85W-140 GL-5 is designed for use in highly loaded, hypoid gears for hypoid gearbox, as well as for axle, transfer case, transmission gear, auxiliary gearboxes in vehicles and machinery and for use as extreme pressure gear oil where this grade of lubricant is specified by the manufacturer.
Characteristics
- a very good oxidation stability
- widest possible protection against rust and corrosion
- no foam formation
- excellent extreme pressure properties
- low pour point
- neutral behaviour towards metals and sealing materials
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 85W-140 |
85W-140
|
||
| Type | Mineral |
Mineral
|
||
| API | GL-5 |
GL-5
|
||
| Recomendations | CS 3000B, Ford SQ-M2C 9002-A, MAN 342 Type M1, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 16D, ZF TE-ML 21A |
CS 3000B, Ford SQ-M2C 9002-A, MAN 342 Type M1, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 16D, ZF TE-ML 21A
|
||
| specification | MIL-L-2105 D |
MIL-L-2105 D
|
||
| Suitable for | GM |
GM
|
||
| Density at 20 °C | g/cm³ | 894 | EN ISO 12185 |
894
g/cm³
EN ISO 12185
|
| Color | Brown | visual |
Brown
visual
|
|
| Viscosity at 100 °C | mm²/s | 26.4 | DIN 51562-1 |
26.4
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 355 | DIN 51562-1 |
355
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 99 | DIN ISO 2909 |
99
DIN ISO 2909
|
|
| Brookfield Viscosity at -12 °C | mPa*s | 55.000 | ASTM D2983 |
55.000
mPa*s
ASTM D2983
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | CS 3000B, Ford SQ-M2C 9002-A, MAN 342 Type M1, MIL-L-2105 D, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 16D, ZF TE-ML 21A |
CS 3000B, Ford SQ-M2C 9002-A, MAN 342 Type M1, MIL-L-2105 D, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 16D, ZF TE-ML 21A
|
||
| Recommendations | CS 3000B, Ford M2C-9002 A, GM, MAN 342 M1, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 16D, ZF TE-ML 21A |
CS 3000B, Ford M2C-9002 A, GM, MAN 342 M1, Mack GO-G, ZF TE-ML 05A, ZF TE-ML 16D, ZF TE-ML 21A
|
RAVENOL Getriebeoel MZG SAE 80W-90 GL-4
For transmission
RAVENOL Getriebeoel MZG SAE 80W-90 GL contains high-quality base oils with a balanced active agent component additive. This ensures a high load carrying capacity, wear protection and oxidation stability.Above-average viscosity-temperature properties, low solidification points and last but not least the prevention of foaming allows for use at various operating conditions.
Manufacturer Approved:
ZF TE-ML 16A, ZF TE-ML 17A, ZF TE-ML 19A
Compliance with the requirements:
DTFR 13B100 (MB 235.1), Ford SQM-2C 9008-A, MAN 341 Type E1, MAN 341 Type Z1, MB 235.1, MB 235.14, ZF TE-ML 02B
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1223105-001
1223105-001-01-999
Code:
4014835734616
Volume:
4 L
Vendor code:
1223105-004
1223105-004-01-999
Code:
4014835734692
Volume:
10 L
Vendor code:
1223105-010
1223105-010-01-999
Code:
4014835734647
Volume:
20 L
Vendor code:
1223105-020
1223105-020-01-999
Code:
4014835734623
Volume:
20 L, ecobox
Vendor code:
1223105-B20
1223105-B20-01-888
Code:
4014835789425
Volume:
60 L
Vendor code:
1223105-060
1223105-060-01-999
Code:
4014835734661
Volume:
208 L
Vendor code:
1223105-208
1223105-208-01-999
Code:
4014835734685
Volume:
1000 L
Vendor code:
1223105-700
1223105-700-01-999
Code:
4014835734678
Application instructions
RAVENOL Getriebeoel MZG SAE 80W-90 GL is suitable for lubricating manual transmissions, differential- and steering gears in vehicles requiring EP transmission oil according to manufacturer specifications.
Characteristics
- well adhering, pressure resistant lubricating films
- excellent oxidation stability
- above-average viscosity-temperature properties
- anti-wear effect
- good air release characteristics, no foaming
- neutral to metal and sealants
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 80W-90 |
80W-90
|
||
| Type | Mineral |
Mineral
|
||
| API | GL-4 |
GL-4
|
||
| Manufacturer Approved | ZF TE-ML 16A, ZF TE-ML 17A, ZF TE-ML 19A |
ZF TE-ML 16A, ZF TE-ML 17A, ZF TE-ML 19A
|
||
| Recomendations | DTFR 13B100 (MB 235.1), Ford SQM-2C 9008-A, MAN 341 Type E1, MAN 341 Type Z1, MB 235.1, MB 235.14, ZF TE-ML 02B |
DTFR 13B100 (MB 235.1), Ford SQM-2C 9008-A, MAN 341 Type E1, MAN 341 Type Z1, MB 235.1, MB 235.14, ZF TE-ML 02B
|
||
| specification | MIL-L-2105 D |
MIL-L-2105 D
|
||
| Density at 20 °C | g/cm³ | 879 | EN ISO 12185 |
879
g/cm³
EN ISO 12185
|
| Color | tan | visual |
tan
visual
|
|
| Viscosity at 100 °C | mm²/s | 14 | DIN 51562-1 |
14
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 126.9 | DIN 51562-1 |
126.9
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 108 | DIN ISO 2909 |
108
DIN ISO 2909
|
|
| Brookfield Viscosity at -26 °C | mPa*s | 45.600 | ASTM D2983 |
45.600
mPa*s
ASTM D2983
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | DTFR 13B100 (MB 235.1), Ford SQM-2C 9008-A, MAN 341 Type E1, MAN 341 Type Z1, MB 235.1, MB 235.14, MIL-L-2105 D, ZF TE-ML 02B, ZF TE-ML 16A, ZF TE-ML 17A, ZF TE-ML 19A |
DTFR 13B100 (MB 235.1), Ford SQM-2C 9008-A, MAN 341 Type E1, MAN 341 Type Z1, MB 235.1, MB 235.14, MIL-L-2105 D, ZF TE-ML 02B, ZF TE-ML 16A, ZF TE-ML 17A, ZF TE-ML 19A
|
||
| Recommendations | DTFR 13B100 (MB 235.1), Ford SQM-2C-9008 A, MAN 341 E1, MAN 341 Z1, MB 235.1, MB 235.14, ZF TE-ML 02B |
DTFR 13B100 (MB 235.1), Ford SQM-2C-9008 A, MAN 341 E1, MAN 341 Z1, MB 235.1, MB 235.14, ZF TE-ML 02B
|
Hydraulic clutch system
RAVENOL DOT 4
For brake system
RAVENOL DOT 4 is a brake fluid for the use in all vehicles with optimum ABS characteristics. There is a chemical stability and it is provided with additives which save the best lubrication efficiency.
- Available packaging
- Product parameters
Volume:
250 ml
Vendor code:
1350601-250
1350601-250-05-000
Code:
4014835692121
Volume:
500 ml
Vendor code:
1350601-500
1350601-500-05-000
Code:
4014835692152
Volume:
1 L
Vendor code:
1350601-001
1350601-001-01-000
Code:
4014835692114
Volume:
20 L
Vendor code:
1350601-020
Because of the special formulation of RAVENOL DOT 4 the international specifications SAE J 1704, ISO 4925 and the safety regulations FMVSS 116 DOT 3 and DOT 4 from the United States of America are exceeded.
Application Note
RAVENOL DOT can be used in all vehicles for which the DOT 4 specification for brake fluids is required. It is suitable for all hydraulic brake systems with synthetic fluids.
RAVENOL DOT is miscible with all known brake fluids of the same specification. To use the high performance level of RAVENOL DOT , a complete change of the brake fluid is recommended.
RAVENOL DOT is not suitable for vehicles with mineral oil systems (e.g. certain Citroën models).
FOLLOW VEHICLE MANUFACTURERS RECOMMENDATIONS WHEN ADDING BRAKE FLUID KEEP BRAKE FLUID CLEAN AND DRY. Contamination with dirt, water, petroleum products or other materials may result in brake failure or costly repairs.
STORE BRAKE FLUID ONLY IN ITS ORIGINAL CONTAINER. KEEP CONTAINER CLEAN AND TIGHTLY CLOSED TO PREVENT ADSORPTION OF WATER. CAUTION! DO NOT REFILL CONTAINER AND DO NOT USE FOR OTHER LIQUIDS.
Dispose of used brake fluid responsibly (EU waste code 160113).
Brake fluid damages paint work –if spilt wash off immediately with plenty of water.
Characteristics
- optimum ABS characteristics
- chemical stability
- best lubrication efficiency
- neutral behaviour regarding brake parts
- low viscosity at low temperatures
- miscible with all brake fluids of the same specifications
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| Type | Synthetic |
Synthetic
|
||
| specification | DOT 4, ISO 4925 Class 4, SAE J 1704 |
DOT 4, ISO 4925 Class 4, SAE J 1704
|
||
| Density at 20 °C | g/cm³ | 1052 | EN ISO 12185 |
1052
g/cm³
EN ISO 12185
|
| Color | light yellow | visual |
light yellow
visual
|
|
| Viscosity at 100 °C | mPa*s | 2.41 | ASTM D445 |
2.41
mPa*s
ASTM D445
|
| Viscosity at -40 °C | cSt | 1340 | ASTM D445 |
1340
cSt
ASTM D445
|
| Wet Equilibrium Reflux Boiling Point | °C | 169 | FMVSS 116 |
169
°C
FMVSS 116
|
| High Temperature Stability | °C | -1 | FMVSS 116 |
-1
°C
FMVSS 116
|
| Chemical Stability | °C | 1 | FMVSS 116 |
1
°C
FMVSS 116
|
| Evaporation | %w/w | 61 | FMVSS 116 |
61
%w/w
FMVSS 116
|
| Fluidity & Appearance at -40 °C | i.O., 4s | FMVSS 116 |
i.O., 4s
FMVSS 116
|
|
| Fluidity & Appearance at -50 °C | i.O., 8s | FMVSS 116 |
i.O., 8s
FMVSS 116
|
|
| Water Tolerance at -40 °C | transparent, 3s | FMVSS 116 |
transparent, 3s
FMVSS 116
|
|
| Water Tolerance at +60 °C | Transparent | FMVSS 116 |
Transparent
FMVSS 116
|
|
| Compatibility at -40 °C | Transparent | FMVSS 116 |
Transparent
FMVSS 116
|
|
| Compatibility at +60 °C | Transparent | FMVSS 116 |
Transparent
FMVSS 116
|
|
| Tinned Iron | Δ mg/cm² | 0.04 | FMVSS 116 |
0.04
Δ mg/cm²
FMVSS 116
|
| Steel | mg/cm² | -0.01 | FMVSS 116 |
-0.01
mg/cm²
FMVSS 116
|
| Aluminium | mg/cm² | 0.02 | FMVSS 116 |
0.02
mg/cm²
FMVSS 116
|
| Cast Iron | Δ mg/cm² | -0,03 | FMVSS 116 |
-0,03
Δ mg/cm²
FMVSS 116
|
| Brass | mg/cm² | -0.08 | FMVSS 116 |
-0.08
mg/cm²
FMVSS 116
|
| Copper | mg/cm² | -0.05 | FMVSS 116 |
-0.05
mg/cm²
FMVSS 116
|
| Zinc | mg/cm² | 0.01 | FMVSS 116 |
0.01
mg/cm²
FMVSS 116
|
| Rubber Diameter Change | 0.16 | FMVSS 116 |
0.16
FMVSS 116
|
|
| Hardness Change | °IRHD | -4 | FMVSS 116 |
-4
°IRHD
FMVSS 116
|
| Appearance | i.O. | FMVSS 116 |
i.O.
FMVSS 116
|
|
| SBR at 70 °C | mm | 0.56 | FMVSS 116 |
0.56
mm
FMVSS 116
|
| SBR at 120 °C | mm | 0.73 | FMVSS 116 |
0.73
mm
FMVSS 116
|
| EPDM at 70 °C (as required by SAE J1703) | IRHD | -2 | FMVSS 116 |
-2
IRHD
FMVSS 116
|
| EPDM at 120 °C | IRHD | -2 | FMVSS 116 |
-2
IRHD
FMVSS 116
|
| Natural at 70 °C (as required by ISO 4925) | mm | 0.38 | FMVSS 116 |
0.38
mm
FMVSS 116
|
| Approvals | DOT 4, ISO 4925 Class 4, SAE J 1704 |
DOT 4, ISO 4925 Class 4, SAE J 1704
|
Hydraulic brake system ABS
RAVENOL DOT 4
For brake system
RAVENOL DOT 4 is a brake fluid for the use in all vehicles with optimum ABS characteristics. There is a chemical stability and it is provided with additives which save the best lubrication efficiency.
- Available packaging
- Product parameters
Volume:
250 ml
Vendor code:
1350601-250
1350601-250-05-000
Code:
4014835692121
Volume:
500 ml
Vendor code:
1350601-500
1350601-500-05-000
Code:
4014835692152
Volume:
1 L
Vendor code:
1350601-001
1350601-001-01-000
Code:
4014835692114
Volume:
20 L
Vendor code:
1350601-020
Because of the special formulation of RAVENOL DOT 4 the international specifications SAE J 1704, ISO 4925 and the safety regulations FMVSS 116 DOT 3 and DOT 4 from the United States of America are exceeded.
Application Note
RAVENOL DOT can be used in all vehicles for which the DOT 4 specification for brake fluids is required. It is suitable for all hydraulic brake systems with synthetic fluids.
RAVENOL DOT is miscible with all known brake fluids of the same specification. To use the high performance level of RAVENOL DOT , a complete change of the brake fluid is recommended.
RAVENOL DOT is not suitable for vehicles with mineral oil systems (e.g. certain Citroën models).
FOLLOW VEHICLE MANUFACTURERS RECOMMENDATIONS WHEN ADDING BRAKE FLUID KEEP BRAKE FLUID CLEAN AND DRY. Contamination with dirt, water, petroleum products or other materials may result in brake failure or costly repairs.
STORE BRAKE FLUID ONLY IN ITS ORIGINAL CONTAINER. KEEP CONTAINER CLEAN AND TIGHTLY CLOSED TO PREVENT ADSORPTION OF WATER. CAUTION! DO NOT REFILL CONTAINER AND DO NOT USE FOR OTHER LIQUIDS.
Dispose of used brake fluid responsibly (EU waste code 160113).
Brake fluid damages paint work –if spilt wash off immediately with plenty of water.
Characteristics
- optimum ABS characteristics
- chemical stability
- best lubrication efficiency
- neutral behaviour regarding brake parts
- low viscosity at low temperatures
- miscible with all brake fluids of the same specifications
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| Type | Synthetic |
Synthetic
|
||
| specification | DOT 4, ISO 4925 Class 4, SAE J 1704 |
DOT 4, ISO 4925 Class 4, SAE J 1704
|
||
| Density at 20 °C | g/cm³ | 1052 | EN ISO 12185 |
1052
g/cm³
EN ISO 12185
|
| Color | light yellow | visual |
light yellow
visual
|
|
| Viscosity at 100 °C | mPa*s | 2.41 | ASTM D445 |
2.41
mPa*s
ASTM D445
|
| Viscosity at -40 °C | cSt | 1340 | ASTM D445 |
1340
cSt
ASTM D445
|
| Wet Equilibrium Reflux Boiling Point | °C | 169 | FMVSS 116 |
169
°C
FMVSS 116
|
| High Temperature Stability | °C | -1 | FMVSS 116 |
-1
°C
FMVSS 116
|
| Chemical Stability | °C | 1 | FMVSS 116 |
1
°C
FMVSS 116
|
| Evaporation | %w/w | 61 | FMVSS 116 |
61
%w/w
FMVSS 116
|
| Fluidity & Appearance at -40 °C | i.O., 4s | FMVSS 116 |
i.O., 4s
FMVSS 116
|
|
| Fluidity & Appearance at -50 °C | i.O., 8s | FMVSS 116 |
i.O., 8s
FMVSS 116
|
|
| Water Tolerance at -40 °C | transparent, 3s | FMVSS 116 |
transparent, 3s
FMVSS 116
|
|
| Water Tolerance at +60 °C | Transparent | FMVSS 116 |
Transparent
FMVSS 116
|
|
| Compatibility at -40 °C | Transparent | FMVSS 116 |
Transparent
FMVSS 116
|
|
| Compatibility at +60 °C | Transparent | FMVSS 116 |
Transparent
FMVSS 116
|
|
| Tinned Iron | Δ mg/cm² | 0.04 | FMVSS 116 |
0.04
Δ mg/cm²
FMVSS 116
|
| Steel | mg/cm² | -0.01 | FMVSS 116 |
-0.01
mg/cm²
FMVSS 116
|
| Aluminium | mg/cm² | 0.02 | FMVSS 116 |
0.02
mg/cm²
FMVSS 116
|
| Cast Iron | Δ mg/cm² | -0,03 | FMVSS 116 |
-0,03
Δ mg/cm²
FMVSS 116
|
| Brass | mg/cm² | -0.08 | FMVSS 116 |
-0.08
mg/cm²
FMVSS 116
|
| Copper | mg/cm² | -0.05 | FMVSS 116 |
-0.05
mg/cm²
FMVSS 116
|
| Zinc | mg/cm² | 0.01 | FMVSS 116 |
0.01
mg/cm²
FMVSS 116
|
| Rubber Diameter Change | 0.16 | FMVSS 116 |
0.16
FMVSS 116
|
|
| Hardness Change | °IRHD | -4 | FMVSS 116 |
-4
°IRHD
FMVSS 116
|
| Appearance | i.O. | FMVSS 116 |
i.O.
FMVSS 116
|
|
| SBR at 70 °C | mm | 0.56 | FMVSS 116 |
0.56
mm
FMVSS 116
|
| SBR at 120 °C | mm | 0.73 | FMVSS 116 |
0.73
mm
FMVSS 116
|
| EPDM at 70 °C (as required by SAE J1703) | IRHD | -2 | FMVSS 116 |
-2
IRHD
FMVSS 116
|
| EPDM at 120 °C | IRHD | -2 | FMVSS 116 |
-2
IRHD
FMVSS 116
|
| Natural at 70 °C (as required by ISO 4925) | mm | 0.38 | FMVSS 116 |
0.38
mm
FMVSS 116
|
| Approvals | DOT 4, ISO 4925 Class 4, SAE J 1704 |
DOT 4, ISO 4925 Class 4, SAE J 1704
|
Lubrication points oilers, other
RAVENOL Mehrzweckfett OML
For lubrication
RAVENOL Mehrzweckfett OML is lithium saponified multipurpose grease with oxidation and corrosion protective additives.
- Available packaging
- Product parameters
Volume:
100 g
Vendor code:
1340101-100
1340101-100-04-999
Code:
4014835844339
Volume:
200 g
Vendor code:
1340101-200
Volume:
400 g
Vendor code:
1340101-400
1340101-400-04-999
Code:
4014835768048
Volume:
5 kg
Vendor code:
1340101-005
1340101-005-03-000
Code:
4014835200159
Volume:
10 kg
Vendor code:
1340101-010
1340101-010-03-000
Code:
4014835200111
Volume:
15 kg
Vendor code:
1340101-015
Volume:
25 kg
Vendor code:
1340101-025
1340101-025-03-000
Code:
4014835200128
Volume:
180 kg
Vendor code:
1340101-180
1340101-180-03-000
Code:
4014835200142
RAVENOL Mehrzweckfett OML has an extreme mechanical stability and a very low friction value. Therefore it can be transported easily.
Application instructions
RAVENOL Mehrzweckfett OML is used for the lubrication of easy loaded antifriction bearings and machine components. It is also suited as multipurpose lubrication grease for vehicles.
Characteristics
- Universal use, multipurpose characteristic for a mixed car pool
- Extreme shear stability
- Excellent corrosion protection
- Excellent wear protection
- Very good mechanical and chemical stability
- Very good aging resistant
- Good pumpability, even at low temperatures
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| specification | DIN 51502 K2K-30, ISO 6743-9: ISO-L-XCCEA2 |
DIN 51502 K2K-30, ISO 6743-9: ISO-L-XCCEA2
|
||
| Color | Light brown | visual |
Light brown
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| NLGI-Class | 2 | DIN 51818 |
2
DIN 51818
|
|
| Product Classification | K2K-30 | DIN 51502 |
K2K-30
DIN 51502
|
|
| Short term temperature up to | °C | 130 | DIN 51757 |
130
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 265-295 | ISO 2137 |
265-295
ISO 2137
|
|
| Corrosion (SKF Emcor dist. Water) | 1 | DIN 51802 |
1
DIN 51802
|
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 130 | DIN 51562-1 |
130
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 K2K-30, ISO 6743-9: ISO-L-XCCEA2 |
DIN 51502 K2K-30, ISO 6743-9: ISO-L-XCCEA2
|
RAVENOL Mehrzweckfett mit Graphit
For lubrication
RAVENOL Mehrzweckfett mit Graphit is a lithium saponified multipurpose grease with finely divided graphite to increase heavy loads at very high temperatures.
- Available packaging
- Product parameters
Volume:
1 kg
Vendor code:
1340102-001
1340102-001-03-000
Code:
4014835200210
Volume:
5 kg
Vendor code:
1340102-005
1340102-005-03-000
Code:
4014835200265
Volume:
10 kg
Vendor code:
1340102-010
1340102-010-03-000
Code:
4014835200227
Volume:
15 kg
Vendor code:
1340102-015
Volume:
25 kg
Vendor code:
1340102-025
1340102-025-03-000
Code:
4014835200258
Volume:
100 g
Vendor code:
1340102-100
1340102-100-04-999
Code:
4014835844391
Volume:
180 kg
Vendor code:
1340102-180
1340102-180-03-000
Code:
4014835200272
Volume:
200 g
Vendor code:
1340102-200
Volume:
400 g
Vendor code:
1340102-400
1340102-400-04-999
Code:
4014835768147
RAVENOL Mehrzweckfett mit Graphit is formulated with a highly refined base oil mixture which contains less than 3% polycyclic aromatics.Through the graphite at high temperatures a lubrication film on the metals is formed, and the graphite takes lubrication to achieve optimal results.
The optimized formulation of RAVENOL Mehrzweckfett mit Graphit can also capture temperature peaks in the application.
Application instructions
RAVENOL Mehrzweckfett mit Graphit has been designed for applications exposed to high temperatures and shock loads.
RAVENOL Mehrzweckfett mit Graphit is used in oven conveyor belts, pistons in hydraulic pumps and all types of bearings that run at low speeds.
RAVENOL Mehrzweckfett mit Graphit is also used as a sealant in high temperature gaskets from steam pipes and other hot pipe connections.
Characteristics
- Extreme shear stability
- Excellent corrosion protection
- Very good mechanical and chemical stability
- Very good aging resistant
- Good pump output also at low temperatures
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| specification | DIN 51502 KPF2K-30, ISO I6743-9: ISO-L-XCCFB2 |
DIN 51502 KPF2K-30, ISO I6743-9: ISO-L-XCCFB2
|
||
| Color | Black gray | visual |
Black gray
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| Additives | graphite | DIN 51757 |
graphite
DIN 51757
|
|
| NLGI-Class | 2 | DIN 51818 |
2
DIN 51818
|
|
| Product Classification | KPF2K-30 | DIN 51502 |
KPF2K-30
DIN 51502
|
|
| Short term temperature up to | °C | 130 | DIN 51757 |
130
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 265-295 | ISO 2137 |
265-295
ISO 2137
|
|
| Corrosion (SKF Emcor dist. Water) | 1 | DIN 51802 |
1
DIN 51802
|
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 80 | DIN 51562-1 |
80
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 KPF2K-30, ISO I6743-9: ISO-L-XCCFB2 |
DIN 51502 KPF2K-30, ISO I6743-9: ISO-L-XCCFB2
|
RAVENOL Mehrzweckfett mit MoS-2
For CV joint
RAVENOL Mehrzweckfett mit MoS2 is a lithium saponified multipurpose grease with finely divided MoS2 to increase heavy loads at very high temperatures.
- Available packaging
- Product parameters
Volume:
1 kg
Vendor code:
1340103-001
1340103-001-03-000
Code:
4014835200333
Volume:
5 kg
Vendor code:
1340103-005
1340103-005-03-000
Code:
4014835200357
Volume:
10 kg
Vendor code:
1340103-010
1340103-010-03-000
Code:
4014835200319
Volume:
15 kg
Vendor code:
1340103-015
Volume:
25 kg
Vendor code:
1340103-025
1340103-025-03-000
Code:
4014835200326
Volume:
100 g
Vendor code:
1340103-100
1340103-100-04-999
Code:
4014835844452
Volume:
180 kg
Vendor code:
1340103-180
1340103-180-03-000
Code:
4014835200371
Volume:
200 g
Vendor code:
1340103-200
Volume:
400 g
Vendor code:
1340103-400
1340103-400-04-999
Code:
4014835768246
RAVENOL Mehrzweckfett mit MoS2 is formulated with a highly refined base oil mixture which contains less than 3% polycyclic aromatics.
The optimized formulation of RAVENOL Mehrzweckfett mit MoS2 has distinctive friction-reducing properties and so-called dry running properties.
Application instructions
RAVENOL Mehrzweckfett mit MoS2 has been designed for applications exposed to extreme pressure and shock loaded bearings with relatively slow sliding movements.
RAVENOL Mehrzweckfett mit MoS2 is recommended for friction and roller bearings of all types during aggravated operating conditions.
RAVENOL Mehrzweckfett mit MoS2 is also used for chassis lubricating.
Characteristics
- Extreme shear stability
- Excellent corrosion protection
- Very good mechanical and chemical stability
- Very good aging resistant
- Good pump output also at low temperatures
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| specification | DIN 51502 KPF2K-30, ISO 6743-9: ISO-L-XCCIB2 |
DIN 51502 KPF2K-30, ISO 6743-9: ISO-L-XCCIB2
|
||
| Color | Black gray | visual |
Black gray
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| Additives | molybdenum disulfide | DIN 51757 |
molybdenum disulfide
DIN 51757
|
|
| NLGI-Class | 2 | DIN 51818 |
2
DIN 51818
|
|
| Product Classification | KPF2K-30 | DIN 51502 |
KPF2K-30
DIN 51502
|
|
| Short term temperature up to | °C | 130 | DIN 51757 |
130
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 265-295 | ISO 2137 |
265-295
ISO 2137
|
|
| Corrosion (SKF Emcor dist. Water) | 1 | DIN 51802 |
1
DIN 51802
|
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 80 | DIN 51562-1 |
80
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 KPF2K-30, ISO 6743-9: ISO-L-XCCIB2 |
DIN 51502 KPF2K-30, ISO 6743-9: ISO-L-XCCIB2
|
RAVENOL LKW FETT BLAU
For bearings
RAVENOL LKW FETT BLAU is a lithium saponified multipurpose grease on mineral basis with oxidation and corrosion protective additives.
Manufacturer Approved:
DTFR 33B120 (MB 267.0), MAN 283 Li-P2, MB-Approval 267.0
Compliance with the requirements:
VW G 052 180
- Available packaging
- Product parameters
Volume:
1 kg
Vendor code:
1340117-001
1340117-001-03-000
Code:
4014835661714
Volume:
5 kg
Vendor code:
1340117-005
1340117-005-03-000
Code:
4014835661752
Volume:
10 kg
Vendor code:
1340117-010
1340117-010-03-000
Code:
4014835661776
Volume:
15 kg
Vendor code:
1340117-015
Volume:
25 kg
Vendor code:
1340117-025
1340117-025-03-000
Code:
4014835661721
Volume:
180 kg
Vendor code:
1340117-180
Volume:
400 g
Vendor code:
1340117-400
1340117-400-04-999
Code:
4014835768543
Because of its special additivation RAVENOL LKW FETT BLAU has an excellent pressure absorption capacity, excellent corrosion protection characteristics and a superior mechanical stability.
Application instructions
RAVENOL LKW FETT BLAU is used for the lubrication of high loaded friction and antifriction bearings of trucks and construction machines even under the influence of humidity, vibration and shock loading. Functional range from - 30°C up + 125°C (maximum + 140°C). NLGI class 2. Extended lubrication intervals.
Characteristics
- Extreme shear stability
- Excellent corrosion protection
- Very good mechanical and chemical stability
- Very good aging resistance
- Good pump output also at low temperatures
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| Type | Mineral |
Mineral
|
||
| Manufacturer Approved | DTFR 33B120 (MB 267.0), MAN 283 Li-P2, MB-Approval 267.0 |
DTFR 33B120 (MB 267.0), MAN 283 Li-P2, MB-Approval 267.0
|
||
| Recomendations | VW G 052 180 |
VW G 052 180
|
||
| specification | DIN 51502 KP2N-30, ISO 6743-9, ISO-L XCDEB2, Volvo 97720, Volvo STD |
DIN 51502 KP2N-30, ISO 6743-9, ISO-L XCDEB2, Volvo 97720, Volvo STD
|
||
| Color | Blue | visual |
Blue
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| NLGI-Class | 2 | DIN 51818 |
2
DIN 51818
|
|
| Product Classification | KP2N-30 | DIN 51502 |
KP2N-30
DIN 51502
|
|
| Short term temperature up to | °C | 220 | DIN 51757 |
220
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 265-295 | ISO 2137 |
265-295
ISO 2137
|
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 220 | DIN 51562-1 |
220
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 KP2N-30, DTFR 33B120 (MB 267.0), ISO 6743-9, ISO-L XCDEB2, MAN 283 Li-P2, MB 267.0, VW G 052 180, Volvo 97720, Volvo STD |
DIN 51502 KP2N-30, DTFR 33B120 (MB 267.0), ISO 6743-9, ISO-L XCDEB2, MAN 283 Li-P2, MB 267.0, VW G 052 180, Volvo 97720, Volvo STD
|
||
| Recommendations | VW/Audi G 052 180 A1 |
VW/Audi G 052 180 A1
|
Hydraulic system of throw-back cab
For brake system
RAVENOL LHM PLUS Fluid is special semisynthetic hydraulic fluid especially designed for use in vehicles of the PSA group (Citroen, Peugeot).
- Available packaging
- Product parameters
Volume:
4 L
Vendor code:
1181110-004
Volume:
20 L
Vendor code:
1181110-020
Volume:
20 L, ecobox
Vendor code:
1181110-B20
Volume:
1000 L
Vendor code:
1181110-700
Due to its special formulation RAVENOL LHM PLUS Fluid has significantly improved low temperature viscosity and fulfils the PSA approval specification.
Application instructions
RAVENOL LHM PLUS Fluid is used in vehicles with appropriately marked fluid reservoir for the hydraulic operation or support of braking, steering and suspension functions.
RAVENOL LHM PLUS Fuid is miscible with earlier LHM fluids.
Characteristics
- A low pour point.
- Excellent viscosity behavior at low temperatures.
- An extremely high viscosity index.
- Low viscosity at low temperatures.
- Neutral behavior towards sealing materials.
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| Type | Semi-synthetic |
Semi-synthetic
|
||
| specification | ISO 7308, PSA B71 2710 |
ISO 7308, PSA B71 2710
|
||
| Density at 20 °C | g/cm³ | 831 | EN ISO 12185 |
831
g/cm³
EN ISO 12185
|
| Color | Green | visual |
Green
visual
|
|
| Viscosity at 100 °C | mm²/s | 7.2 | DIN 51562-1 |
7.2
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 25.3 | DIN 51562-1 |
25.3
mm²/s
DIN 51562-1
|
| Viscosity at -40 °C | 2600 | ASTM D445 |
2600
ASTM D445
|
|
| Viscosity Index VI | 273 | DIN ISO 2909 |
273
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 3460 | ASTM D2983 |
3460
mPa*s
ASTM D2983
|
| Approvals | ISO 7308, PSA B71 2710 |
ISO 7308, PSA B71 2710
|
Central lubrication system grease
RAVENOL Mehrzweckfett OML
For lubrication
RAVENOL Mehrzweckfett OML is lithium saponified multipurpose grease with oxidation and corrosion protective additives.
- Available packaging
- Product parameters
Volume:
100 g
Vendor code:
1340101-100
1340101-100-04-999
Code:
4014835844339
Volume:
200 g
Vendor code:
1340101-200
Volume:
400 g
Vendor code:
1340101-400
1340101-400-04-999
Code:
4014835768048
Volume:
5 kg
Vendor code:
1340101-005
1340101-005-03-000
Code:
4014835200159
Volume:
10 kg
Vendor code:
1340101-010
1340101-010-03-000
Code:
4014835200111
Volume:
15 kg
Vendor code:
1340101-015
Volume:
25 kg
Vendor code:
1340101-025
1340101-025-03-000
Code:
4014835200128
Volume:
180 kg
Vendor code:
1340101-180
1340101-180-03-000
Code:
4014835200142
RAVENOL Mehrzweckfett OML has an extreme mechanical stability and a very low friction value. Therefore it can be transported easily.
Application instructions
RAVENOL Mehrzweckfett OML is used for the lubrication of easy loaded antifriction bearings and machine components. It is also suited as multipurpose lubrication grease for vehicles.
Characteristics
- Universal use, multipurpose characteristic for a mixed car pool
- Extreme shear stability
- Excellent corrosion protection
- Excellent wear protection
- Very good mechanical and chemical stability
- Very good aging resistant
- Good pumpability, even at low temperatures
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| specification | DIN 51502 K2K-30, ISO 6743-9: ISO-L-XCCEA2 |
DIN 51502 K2K-30, ISO 6743-9: ISO-L-XCCEA2
|
||
| Color | Light brown | visual |
Light brown
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| NLGI-Class | 2 | DIN 51818 |
2
DIN 51818
|
|
| Product Classification | K2K-30 | DIN 51502 |
K2K-30
DIN 51502
|
|
| Short term temperature up to | °C | 130 | DIN 51757 |
130
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 265-295 | ISO 2137 |
265-295
ISO 2137
|
|
| Corrosion (SKF Emcor dist. Water) | 1 | DIN 51802 |
1
DIN 51802
|
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 130 | DIN 51562-1 |
130
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 K2K-30, ISO 6743-9: ISO-L-XCCEA2 |
DIN 51502 K2K-30, ISO 6743-9: ISO-L-XCCEA2
|
RAVENOL Mehrzweckfett mit Graphit
For lubrication
RAVENOL Mehrzweckfett mit Graphit is a lithium saponified multipurpose grease with finely divided graphite to increase heavy loads at very high temperatures.
- Available packaging
- Product parameters
Volume:
1 kg
Vendor code:
1340102-001
1340102-001-03-000
Code:
4014835200210
Volume:
5 kg
Vendor code:
1340102-005
1340102-005-03-000
Code:
4014835200265
Volume:
10 kg
Vendor code:
1340102-010
1340102-010-03-000
Code:
4014835200227
Volume:
15 kg
Vendor code:
1340102-015
Volume:
25 kg
Vendor code:
1340102-025
1340102-025-03-000
Code:
4014835200258
Volume:
100 g
Vendor code:
1340102-100
1340102-100-04-999
Code:
4014835844391
Volume:
180 kg
Vendor code:
1340102-180
1340102-180-03-000
Code:
4014835200272
Volume:
200 g
Vendor code:
1340102-200
Volume:
400 g
Vendor code:
1340102-400
1340102-400-04-999
Code:
4014835768147
RAVENOL Mehrzweckfett mit Graphit is formulated with a highly refined base oil mixture which contains less than 3% polycyclic aromatics.Through the graphite at high temperatures a lubrication film on the metals is formed, and the graphite takes lubrication to achieve optimal results.
The optimized formulation of RAVENOL Mehrzweckfett mit Graphit can also capture temperature peaks in the application.
Application instructions
RAVENOL Mehrzweckfett mit Graphit has been designed for applications exposed to high temperatures and shock loads.
RAVENOL Mehrzweckfett mit Graphit is used in oven conveyor belts, pistons in hydraulic pumps and all types of bearings that run at low speeds.
RAVENOL Mehrzweckfett mit Graphit is also used as a sealant in high temperature gaskets from steam pipes and other hot pipe connections.
Characteristics
- Extreme shear stability
- Excellent corrosion protection
- Very good mechanical and chemical stability
- Very good aging resistant
- Good pump output also at low temperatures
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| specification | DIN 51502 KPF2K-30, ISO I6743-9: ISO-L-XCCFB2 |
DIN 51502 KPF2K-30, ISO I6743-9: ISO-L-XCCFB2
|
||
| Color | Black gray | visual |
Black gray
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| Additives | graphite | DIN 51757 |
graphite
DIN 51757
|
|
| NLGI-Class | 2 | DIN 51818 |
2
DIN 51818
|
|
| Product Classification | KPF2K-30 | DIN 51502 |
KPF2K-30
DIN 51502
|
|
| Short term temperature up to | °C | 130 | DIN 51757 |
130
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 265-295 | ISO 2137 |
265-295
ISO 2137
|
|
| Corrosion (SKF Emcor dist. Water) | 1 | DIN 51802 |
1
DIN 51802
|
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 80 | DIN 51562-1 |
80
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 KPF2K-30, ISO I6743-9: ISO-L-XCCFB2 |
DIN 51502 KPF2K-30, ISO I6743-9: ISO-L-XCCFB2
|
RAVENOL Mehrzweckfett mit MoS-2
For CV joint
RAVENOL Mehrzweckfett mit MoS2 is a lithium saponified multipurpose grease with finely divided MoS2 to increase heavy loads at very high temperatures.
- Available packaging
- Product parameters
Volume:
1 kg
Vendor code:
1340103-001
1340103-001-03-000
Code:
4014835200333
Volume:
5 kg
Vendor code:
1340103-005
1340103-005-03-000
Code:
4014835200357
Volume:
10 kg
Vendor code:
1340103-010
1340103-010-03-000
Code:
4014835200319
Volume:
15 kg
Vendor code:
1340103-015
Volume:
25 kg
Vendor code:
1340103-025
1340103-025-03-000
Code:
4014835200326
Volume:
100 g
Vendor code:
1340103-100
1340103-100-04-999
Code:
4014835844452
Volume:
180 kg
Vendor code:
1340103-180
1340103-180-03-000
Code:
4014835200371
Volume:
200 g
Vendor code:
1340103-200
Volume:
400 g
Vendor code:
1340103-400
1340103-400-04-999
Code:
4014835768246
RAVENOL Mehrzweckfett mit MoS2 is formulated with a highly refined base oil mixture which contains less than 3% polycyclic aromatics.
The optimized formulation of RAVENOL Mehrzweckfett mit MoS2 has distinctive friction-reducing properties and so-called dry running properties.
Application instructions
RAVENOL Mehrzweckfett mit MoS2 has been designed for applications exposed to extreme pressure and shock loaded bearings with relatively slow sliding movements.
RAVENOL Mehrzweckfett mit MoS2 is recommended for friction and roller bearings of all types during aggravated operating conditions.
RAVENOL Mehrzweckfett mit MoS2 is also used for chassis lubricating.
Characteristics
- Extreme shear stability
- Excellent corrosion protection
- Very good mechanical and chemical stability
- Very good aging resistant
- Good pump output also at low temperatures
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| specification | DIN 51502 KPF2K-30, ISO 6743-9: ISO-L-XCCIB2 |
DIN 51502 KPF2K-30, ISO 6743-9: ISO-L-XCCIB2
|
||
| Color | Black gray | visual |
Black gray
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| Additives | molybdenum disulfide | DIN 51757 |
molybdenum disulfide
DIN 51757
|
|
| NLGI-Class | 2 | DIN 51818 |
2
DIN 51818
|
|
| Product Classification | KPF2K-30 | DIN 51502 |
KPF2K-30
DIN 51502
|
|
| Short term temperature up to | °C | 130 | DIN 51757 |
130
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 265-295 | ISO 2137 |
265-295
ISO 2137
|
|
| Corrosion (SKF Emcor dist. Water) | 1 | DIN 51802 |
1
DIN 51802
|
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 80 | DIN 51562-1 |
80
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 KPF2K-30, ISO 6743-9: ISO-L-XCCIB2 |
DIN 51502 KPF2K-30, ISO 6743-9: ISO-L-XCCIB2
|
RAVENOL LKW FETT BLAU
For bearings
RAVENOL LKW FETT BLAU is a lithium saponified multipurpose grease on mineral basis with oxidation and corrosion protective additives.
Manufacturer Approved:
DTFR 33B120 (MB 267.0), MAN 283 Li-P2, MB-Approval 267.0
Compliance with the requirements:
VW G 052 180
- Available packaging
- Product parameters
Volume:
1 kg
Vendor code:
1340117-001
1340117-001-03-000
Code:
4014835661714
Volume:
5 kg
Vendor code:
1340117-005
1340117-005-03-000
Code:
4014835661752
Volume:
10 kg
Vendor code:
1340117-010
1340117-010-03-000
Code:
4014835661776
Volume:
15 kg
Vendor code:
1340117-015
Volume:
25 kg
Vendor code:
1340117-025
1340117-025-03-000
Code:
4014835661721
Volume:
180 kg
Vendor code:
1340117-180
Volume:
400 g
Vendor code:
1340117-400
1340117-400-04-999
Code:
4014835768543
Because of its special additivation RAVENOL LKW FETT BLAU has an excellent pressure absorption capacity, excellent corrosion protection characteristics and a superior mechanical stability.
Application instructions
RAVENOL LKW FETT BLAU is used for the lubrication of high loaded friction and antifriction bearings of trucks and construction machines even under the influence of humidity, vibration and shock loading. Functional range from - 30°C up + 125°C (maximum + 140°C). NLGI class 2. Extended lubrication intervals.
Characteristics
- Extreme shear stability
- Excellent corrosion protection
- Very good mechanical and chemical stability
- Very good aging resistance
- Good pump output also at low temperatures
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| Type | Mineral |
Mineral
|
||
| Manufacturer Approved | DTFR 33B120 (MB 267.0), MAN 283 Li-P2, MB-Approval 267.0 |
DTFR 33B120 (MB 267.0), MAN 283 Li-P2, MB-Approval 267.0
|
||
| Recomendations | VW G 052 180 |
VW G 052 180
|
||
| specification | DIN 51502 KP2N-30, ISO 6743-9, ISO-L XCDEB2, Volvo 97720, Volvo STD |
DIN 51502 KP2N-30, ISO 6743-9, ISO-L XCDEB2, Volvo 97720, Volvo STD
|
||
| Color | Blue | visual |
Blue
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| NLGI-Class | 2 | DIN 51818 |
2
DIN 51818
|
|
| Product Classification | KP2N-30 | DIN 51502 |
KP2N-30
DIN 51502
|
|
| Short term temperature up to | °C | 220 | DIN 51757 |
220
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 265-295 | ISO 2137 |
265-295
ISO 2137
|
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 220 | DIN 51562-1 |
220
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 KP2N-30, DTFR 33B120 (MB 267.0), ISO 6743-9, ISO-L XCDEB2, MAN 283 Li-P2, MB 267.0, VW G 052 180, Volvo 97720, Volvo STD |
DIN 51502 KP2N-30, DTFR 33B120 (MB 267.0), ISO 6743-9, ISO-L XCDEB2, MAN 283 Li-P2, MB 267.0, VW G 052 180, Volvo 97720, Volvo STD
|
||
| Recommendations | VW/Audi G 052 180 A1 |
VW/Audi G 052 180 A1
|
Lubrication points oilers, bearings
RAVENOL Wälzlagerfett LI-86
For lubrication
RAVENOL Wälzlagerfett LI-86 is lithium saponified multipurpose grease with oxidation and corrosion protective additives.
- Available packaging
- Product parameters
Volume:
400 g
Vendor code:
1340105-400
1340105-400-04-999
Code:
4014835768444
Volume:
1 kg
Vendor code:
1340105-001
1340105-001-03-000
Code:
4014835200838
Volume:
5 kg
Vendor code:
1340105-005
1340105-005-03-000
Code:
4014835200852
Volume:
10 kg
Vendor code:
1340105-010
1340105-010-03-000
Code:
4014835200845
Volume:
15 kg
Vendor code:
1340105-015
Volume:
25 kg
Vendor code:
1340105-025
1340105-025-03-000
Code:
4014835200821
Volume:
100 g
Vendor code:
1340105-100
1340105-100-04-999
Code:
4014835844575
Volume:
180 kg
Vendor code:
1340105-180
1340105-180-03-000
Code:
4014835200876
Volume:
200 g
Vendor code:
1340105-200
RAVENOL Wälzlagerfett LI-86 is walk stable, stain-resistant and water-repellent.
RAVENOL Wälzlagerfett LI-86 offers excellent adhesion to metal.
Application instructions
RAVENOL Wälzlagerfett LI-86 is suitable for lubrication of all types of vehicle parts and industrial machines. Usable for lubrication of ball and roller bearings. Particularly recommended for chassis lubrication, construction machines and agricultural equipment also for use under tropical conditions.
Characteristics
- Universal use, multipurpose characteristic for a mixed car pool
- Extreme shear stability
- Excellent corrosion protection
- Very good mechanical and chemical stability
- Very good aging resistant
- Good pump output also at low temperatures
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| specification | DIN 51502 K3K-30, ISO 6743-9: ISO-L-XCCFA3 |
DIN 51502 K3K-30, ISO 6743-9: ISO-L-XCCFA3
|
||
| Color | Light brown | visual |
Light brown
visual
|
|
| Thickener | lithium soap | DIN 51757 |
lithium soap
DIN 51757
|
|
| NLGI-Class | 3 | DIN 51818 |
3
DIN 51818
|
|
| Product Classification | K3K-30 | DIN 51502 |
K3K-30
DIN 51502
|
|
| Short term temperature up to | °C | 150 | DIN 51757 |
150
°C
DIN 51757
|
| Worked Penetration at 60 Strokes | 220-250 | ISO 2137 |
220-250
ISO 2137
|
|
| Corrosion (SKF Emcor dist. Water) | 1 | DIN 51802 |
1
DIN 51802
|
|
| Copper Corrosion (24h/120 °C) | 1 | DIN 51811 |
1
DIN 51811
|
|
| Water Resistance (3h/90 °C) | °C | 1-90 | DIN 51807-1 |
1-90
°C
DIN 51807-1
|
| Kinematic Viscosity (Base Oil) at 40 °C | mm²/s | 130 | DIN 51562-1 |
130
mm²/s
DIN 51562-1
|
| Approvals | DIN 51502 K3K-30, ISO 6743-9: ISO-L-XCCFA3 |
DIN 51502 K3K-30, ISO 6743-9: ISO-L-XCCFA3
|
Cooling system
RAVENOL TTC Premix -40°C Protect C11
Coolant
RAVENOL TTC Trad. Techn. Coolant Premix -40°C is a ready to use, prediluted eco-friendly 1.2- Ethanediol (monoethylene glycol) based nitrite, amine and phosphate-free coolant for cooling circuits in combustion engines which provides maintenance-free corrosion and frost protection. The product is formulated as a long-term coolant based on a proven inhibitor development.
Compliance with the requirements:
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
- Available packaging
- Product parameters
Volume:
1.5 L
Vendor code:
1410105-150
1410105-150-01-999
Code:
4014835755314
Volume:
5 L
Vendor code:
1410105-005
1410105-005-01-999
Code:
4014835755352
Volume:
20 L
Vendor code:
1410105-020
1410105-020-01-999
Code:
4014835755321
Volume:
20 L, ecobox
Vendor code:
1410105-B20
1410105-B20-01-888
Code:
4014835855939
Volume:
60 L
Vendor code:
1410105-060
1410105-060-01-999
Code:
4014835755369
Volume:
208 L
Vendor code:
1410105-208
1410105-208-01-999
Code:
4014835755383
Volume:
1000 L
Vendor code:
1410105-700
The quality of an antifreeze is no longer just determined by the antifreeze effect (which automatically exists in an ethylene-glycol based product), but by the rust protection.
That is why manufacturers subject antifreeze to lengthy corrosion and cavitation tests.
RAVENOL TTC Trad. Techn. Coolant Premix -40°C protects the cooling system from rust, frost, and in summer, from overheating.
Application instructions
RAVENOL TTC Trad. Techn. Coolant Premix -40°C is a prediluted coolant with frost and rust protection for year-round use in automotive engines.
Even in summer coolant must contain enough antifreeze to ensure good corrosion and overheating protection.
Instructions: Add RAVENOL TTC Trad. Techn. Coolant Premix -40°C to radiator to fill line.
Characteristics
- Excellent for light metal engines
- Good reserve alkalinity
- High-quality corrosion additives for optimal corrosion protection
- Elastomer compatible with elastome
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| ASTM | D1384, D2570, D2809, D3306, D4985, D6210 Type 1-FF |
D1384, D2570, D2809, D3306, D4985, D6210 Type 1-FF
|
||
| Recomendations | AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C |
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
|
||
| Suitable for | Suzuki |
Suzuki
|
||
| Density at 20 °C | g/cm³ | 1080 | EN ISO 12185 |
1080
g/cm³
EN ISO 12185
|
| Color | yellow green | visual |
yellow green
visual
|
|
| pH - value at 20 °C | 7,8 | ASTM D1287 |
7,8
ASTM D1287
|
|
| Freezing point | °C | -40 | ASTM D1177 |
-40
°C
ASTM D1177
|
| Approvals | AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C |
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
|
||
| Recommendations | AFNOR R15-601, ASTM D1384, ASTM D2570, ASTM D2809, ASTM D3306, ASTM D4985, ASTM D6210 Type 1-FF, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 NF, O Norm V 5123 (Österreich), SAE J1034, Suzuki, UNE 25-361 (Spanien), VW TL 774-C (entspricht G11) |
AFNOR R15-601, ASTM D1384, ASTM D2570, ASTM D2809, ASTM D3306, ASTM D4985, ASTM D6210 Type 1-FF, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 NF, O Norm V 5123 (Österreich), SAE J1034, Suzuki, UNE 25-361 (Spanien), VW TL 774-C (entspricht G11)
|
RAVENOL TTC Concentrate Protect C11
Coolant
RAVENOL TTC Trad. Techn. Coolant Concentrate is an eco-friendly 1.2- Ethanediol (monoethylene glycol) based nitrite, amine and phosphate-free coolant for cooling circuits in combustion engines which provides maintenance-free corrosion and frost protection. The product is formulated as a long-term coolant based on a proven inhibitor development.
Compliance with the requirements:
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
- Available packaging
- Product parameters
Volume:
1.5 L
Vendor code:
1410100-150
1410100-150-01-999
Code:
4014835755215
Volume:
5 L
Vendor code:
1410100-005
1410100-005-01-999
Code:
4014835755253
Volume:
10 L
Vendor code:
1410100-010
Volume:
20 L
Vendor code:
1410100-020
1410100-020-01-999
Code:
4014835755222
Volume:
20 L, ecobox
Vendor code:
1410100-B20
Volume:
60 L
Vendor code:
1410100-060
1410100-060-01-999
Code:
4014835755260
Volume:
60 L, plastic
Vendor code:
1410100-060-01-995
Code:
4014835755239
Volume:
60 L, print
Vendor code:
1410100-D60
Volume:
208 L
Vendor code:
1410100-208
1410100-208-01-995
Code:
4014835755208
Volume:
1000 L
Vendor code:
1410100-700
It is no longer just the anti-freeze effect (which automatically exists in an ethylene-glycol based product) which is critical for the quality of a coolant, but also the rust protection.
Therefore manufacturers subject coolants to long corrosion and cavitation tests.
RAVENOL TTC Trad. Techn. Coolant Concentrate protects the cooling system from corrosion, frost, and in the summer from overheating.
Application instructions
RAVENOL TTC Trad. Techn. Coolant Concentrate with frost and rust protection. Use according to the mixing chart. Follow manufacturer’s recommendations.
Even in summer coolant must contain enough antifreeze to ensure good corrosion and overheating protection.
Instructions: Clean cooling system, check for leaks, flush.
Mix RAVENOL TTC Trad. Techn. Coolant Concentrate with distilled water (per mixing chart) and add. Allow engine and heater to warm up, add coolant to fill level.
| Table of mixing ratios | ||
|---|---|---|
| Antifreeze protection until | Parts Antifreeze | Parts Water |
| -20°C | 35% | 65% |
| -37°C | 50% | 50% |
| -50°C | 60% | 40% |
Characteristics
- Excellent for light metal engines
- Good reserve alkalinity
- High-quality corrosion additives for optimal corrosion protection
- Elastomer compatible with elastomers used in automotive radiators
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| ASTM | D1384, D2809, D3306, D4340, D4985, D6210 Type 1-FF |
D1384, D2809, D3306, D4340, D4985, D6210 Type 1-FF
|
||
| Recomendations | AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C |
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
|
||
| Suitable for | Suzuki |
Suzuki
|
||
| Density at 20 °C | g/cm³ | 1130 | EN ISO 12185 |
1130
g/cm³
EN ISO 12185
|
| Color | yellow green | visual |
yellow green
visual
|
|
| Freezing point (50 % solution) | °C | -37 | ASTM D1177 |
-37
°C
ASTM D1177
|
| pH - value at 20 °C (50 Vol %) | 8,4 | ASTM D1287 |
8,4
ASTM D1287
|
|
| Approvals | AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C |
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
|
||
| Recommendations | AFNOR R15-601, ASTM D1384, ASTM D2809, ASTM D3306, ASTM D4340, ASTM D4985, ASTM D6210 Type 1-FF, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 NF, O Norm V 5123 (Österreich), SAE J1034, Suzuki, UNE 25-361 (Spanien), VW TL 774-C (entspricht G11) |
AFNOR R15-601, ASTM D1384, ASTM D2809, ASTM D3306, ASTM D4340, ASTM D4985, ASTM D6210 Type 1-FF, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 NF, O Norm V 5123 (Österreich), SAE J1034, Suzuki, UNE 25-361 (Spanien), VW TL 774-C (entspricht G11)
|
RAVENOL destilliertes Wasser
For batteries
RAVENOL destilliertes Wasser is deionised distilled water and is manufactured using the ion exchangerprocess.
Compliance with the requirements:
DIN 43530-4, DIN EN 50272
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1360010-001
1360010-001-01-000
Code:
4014835300453
Volume:
5 L
Vendor code:
1360010-005
1360010-005-01-000
Code:
4014835300507
Volume:
5 L, specialist. canister
Vendor code:
1360010-005
1360010-005-01-001
Code:
4014835300514
Volume:
208 L
Vendor code:
1360010-208
Volume:
1000 L
Vendor code:
1360010-700
Volume:
20 L
Vendor code:
1360010-020
1360010-020-01-001
Code:
4014835300422
In the course of this process, the water flows through a column filled with ion exchange resin. This has theability to exchange its accumulated ions for the ions present in the water.
As the ion exchange resin cannot accumulate an infinite number of ions, they have to be “revived”, i.e. theyhave to be regenerated. This takes place using the currently most commonly used regeneration agents: sodiumchloride (water softening), hydrochloric acid (cation exchange) and sodium hydroxide (anion exchange).The conductivity of the water flowing through is constantly checked in a fully automated process and the ionexchanger unit regulates itself automatically.
RAVENOL destilliertes Wasser deionised water is regularly checked by taking samples.
Application instructions
RAVENOL destilliertes Wasser is ideally suited to filling up vehicle batteries and for steam irons and aquariums (to reduce the hardness of the water).
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| Recomendations | DIN 43530-4, DIN EN 50272 |
DIN 43530-4, DIN EN 50272
|
||
| Approvals | DIN 43530-4, DIN EN 50272 |
DIN 43530-4, DIN EN 50272
|
||
| Recommendations | DIN 43 530-4 Akkumulatoren, DIN EN 50272, Elektrolyt und Nachfüllwasser |
DIN 43 530-4 Akkumulatoren, DIN EN 50272, Elektrolyt und Nachfüllwasser
|