Search by VIN, truck make, model, type or unit name, or by the part number of any oil:
Oil for Peterbilt, Tractors for regional transportation, 325 (Paccar PX-6)
Peterbilt Model (Tractors for regional transportation) to find out what kind of oil is used for it
Peterbilt Tractors for regional transportation 325 (Paccar PX-6)from 2010 to 2013 Engine oil, automatic transmission fluid, manual transmission oil, antifreeze, brake fluid, power steering fluid and other fluids.
Power:
Nodes and assemblies
Engine Paccar PX-6
RAVENOL Performance Truck SAE 10W-40
Engine oil
RAVENOL Performance Truck SAE 10W-40 is semi-synthetic multi-grade diesel engine oil for highly loaded diesel engines based on MC-systems.
Manufacturer Approved:
DTFR 15B120, Deutz DQC III-10, MAN M 3277, MTU Type 3, Mack EO-N, Renault RLD-2, TEDOM 258-4, Volvo VDS-3
Compliance with the requirements:
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DAF HP-1, DAF HP-2, DTFR 13D100 (MB 235.27), DTFR 13D110 (MB 235.28), Global DHD-1, MB 228.5, MB 235.27, MB 235.28, Mack EO-M Plus, Scania LDF-2, Voith Retarder B
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1122106-001
Volume:
5 L
Vendor code:
1122106-005
Volume:
10 L
Vendor code:
1122106-010
1122106-010-01-999
Code:
4014835737549
Volume:
20 L
Vendor code:
1122106-020
1122106-020-01-999
Code:
4014835737525
Volume:
20 L, ecobox
Vendor code:
1122106-B20
Volume:
60 L
Vendor code:
1122106-060
1122106-060-01-999
Code:
4014835737563
Volume:
60 L, print
Vendor code:
1122106-D60
1122106-D60-01-888
Code:
4014835737532
Volume:
208 L
Vendor code:
1122106-208
1122106-208-01-999
Code:
4014835737587
Volume:
208 L, print
Vendor code:
1122106-D28
1122106-D28-01-888
Code:
4014835737501
Volume:
1000 L
Vendor code:
1122106-700
RAVENOL Performance Truck SAE 10W-40 is low-friction long-life engine oil for all kind of diesel engines with and without turbocharging in trucks, buses and machinery. Suitable for the longest oil change intervals.
Application instructions
RAVENOL Performance Truck SAE 10W-40 has a higher performance than conventional high-performance engine oils. International such oils are called UHPD oils (UHPD = Ultra High Performance Diesel Oil). Regardless of the particular mileage, older diesel engines on RAVENOL Performance Truck SAE 10W-40 should be changed without rinsing.
Characteristics
- High wear protection even under constant load at full throttle
- Reduced fuel consumption by low-friction characteristics
- Quick oil circulation reduces cold-start and warm-up wear
- Protection against bore polishing of cylinder paths
- Reduction of exhaust particles
- Protects against corrosion, even when using diesel fuels with high sulfur content
- Safe protection against deposits and sticking, both under extreme thermal loads and short haul
- Optimum compatibility with seal materials
- Environmentally friendly due longest oil change intervals and low evaporation losses
- Guaranteed extended drain intervals for the long-haul truck or transport
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 10W-40 |
10W-40
|
||
| Type | Semi-synthetic |
Semi-synthetic
|
||
| API | CF, CI-4 |
CF, CI-4
|
||
| ACEA | E4, E7 |
E4, E7
|
||
| JASO | DH-1 |
DH-1
|
||
| Manufacturer Approved | DTFR 15B120, Deutz DQC III-10, MAN M 3277, MTU Type 3, Mack EO-N, Renault RLD-2, TEDOM 258-4, Volvo VDS-3 |
DTFR 15B120, Deutz DQC III-10, MAN M 3277, MTU Type 3, Mack EO-N, Renault RLD-2, TEDOM 258-4, Volvo VDS-3
|
||
| Recomendations | Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DAF HP-1, DAF HP-2, DTFR 13D100 (MB 235.27), DTFR 13D110 (MB 235.28), Global DHD-1, MB 228.5, MB 235.27, MB 235.28, Mack EO-M Plus, Scania LDF-2, Voith Retarder B |
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DAF HP-1, DAF HP-2, DTFR 13D100 (MB 235.27), DTFR 13D110 (MB 235.28), Global DHD-1, MB 228.5, MB 235.27, MB 235.28, Mack EO-M Plus, Scania LDF-2, Voith Retarder B
|
||
| Density at 20 °C | g/cm³ | 863 | EN ISO 12185 |
863
g/cm³
EN ISO 12185
|
| Color | Dark brown | visual |
Dark brown
visual
|
|
| Viscosity at 100 °C | mm²/s | 15.3 | DIN 51562-1 |
15.3
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 102.1 | DIN 51562-1 |
102.1
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 158 | DIN ISO 2909 |
158
DIN ISO 2909
|
|
| tbn | mgKOH/g | 13.2 | ASTM D2896 |
13.2
mgKOH/g
ASTM D2896
|
| Approvals | Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DAF HP-1, DAF HP-2, DTFR 13D100 (MB 235.27), DTFR 13D110 (MB 235.28), DTFR 15B120, Deutz DQC III-10, Global DHD-1, MAN M 3277, MB 228.5, MB 235.27, MB 235.28, MTU Type 3, Mack EO-M Plus, Mack EO-N, Renault RLD-2, Scania LDF-2, TEDOM 258-4, Voith Retarder B, Volvo VDS-3 |
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DAF HP-1, DAF HP-2, DTFR 13D100 (MB 235.27), DTFR 13D110 (MB 235.28), DTFR 15B120, Deutz DQC III-10, Global DHD-1, MAN M 3277, MB 228.5, MB 235.27, MB 235.28, MTU Type 3, Mack EO-M Plus, Mack EO-N, Renault RLD-2, Scania LDF-2, TEDOM 258-4, Voith Retarder B, Volvo VDS-3
|
||
| Recommendations | Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DAF HP-1, DAF HP-2, DTFR 13D100 (MB 235.27), DTFR 13D110 (MB 235.28), Global DHD-1, JASO DH-1, MB 228.5, MB 235.27, MB 235.28, Mack EO-M Plus, Scania LDF-2, Voith Retarder B |
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DAF HP-1, DAF HP-2, DTFR 13D100 (MB 235.27), DTFR 13D110 (MB 235.28), Global DHD-1, JASO DH-1, MB 228.5, MB 235.27, MB 235.28, Mack EO-M Plus, Scania LDF-2, Voith Retarder B
|
For diesels
RAVENOL Ultra Synthetik Truck SAE 5W-30 is a top quality synthetic fuel economy year-round multigrade diesel engine oil with increased TBN based on the latest additive technology combined with very special base oils.
Manufacturer Approved:
Caterpillar ECF-3, DTFR 15C100, DTFR 15C110, DTFR 15C120, Deutz DQC IV-18 LA, MAN M 3677, MTU Type 3.1, Mack EOS-4.5, Renault RLD-3, Scania LDF-4, Volvo VDS-4.5
Compliance with the requirements:
Cummins CES 20081, Cummins CES 20086, DAF PSQL 2.1E LD, DDC 93K222, DTFR 13D110 (MB 235.28), Deutz TTCD-Motors, Ford WSS-M2C 213-A1, IVECO 18-1804 TLS E6, Liebherr LH-00-ENG LA, MAN M 3271-1, MAN M 3297-1, MAN M 3477, MAN M 3575, MAN M 3691, MAN M 3777, MB 228.31, MB 228.51, MB 235.28, MTU Type 2.1, Scania Low Ash, Voith Retarder B, Volvo CNG
- Available packaging
- Product parameters
Volume:
20 L, ecobox
Vendor code:
1121102-B20
Volume:
60 L
Vendor code:
1121102-060
Volume:
208 L, print
Vendor code:
1121102-D28
Volume:
1000 L
Vendor code:
1121102-700
This fuel saving lubricant has mainly been developed for heavy diesel engines even under the toughest operation conditions and all the year round use.
RAVENOL Ultra Synthetik Truck SAE 5W-30 is suitable for application in engines with or without particle filters and exhaust catalysts. The SAE 5W-30 viscosity range ensures reliable cold starting at low ambient temperatures and full lubricity at high operating temperatures. The use of shearstable additives guarantees that the SAE grade 5W-30 is maintained throughout the entire oil change interval.
RAVENOL Ultra Synthetik Truck SAE 5W-30 is developed as SHPD Motoroil (Super High Performance Diesel). Extended oil change intervals according to manufacturer's specifications.
Application instructions
RAVENOL Ultra Synthetik Truck SAE 5W-30 is a year round high performance motor oil, especially designed for economic use in exhaust-optimized engines with exhaust aftertreatment systems. Follow manufacturer's instructions.
Characteristics
- Increased TBN
- High wear protection
- Outstanding oxidation stability
- Excellent high temperature stability
- Outstanding detergent and dispersant properties
- Efficiency through low fuel consumption
- Long service life due to high oxidation stability
- Outstanding cold start behaviour, rapid engine oiling even at low temperatures
- Very good viscosity-temperature behavior
- Neutrality towards seals
- Low oil consumption due to the low evaporation loss through PAO and HC base oils
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 5W-30 |
5W-30
|
||
| Type | Synthetic |
Synthetic
|
||
| API | CJ-4, CK-4, SN |
CJ-4, CK-4, SN
|
||
| ACEA | E11, E4, E6, E7, E8, E9 |
E11, E4, E6, E7, E8, E9
|
||
| JASO | DH-2 |
DH-2
|
||
| Manufacturer Approved | Caterpillar ECF-3, DTFR 15C100, DTFR 15C110, DTFR 15C120, Deutz DQC IV-18 LA, MAN M 3677, MTU Type 3.1, Mack EOS-4.5, Renault RLD-3, Scania LDF-4, Volvo VDS-4.5 |
Caterpillar ECF-3, DTFR 15C100, DTFR 15C110, DTFR 15C120, Deutz DQC IV-18 LA, MAN M 3677, MTU Type 3.1, Mack EOS-4.5, Renault RLD-3, Scania LDF-4, Volvo VDS-4.5
|
||
| Recomendations | Cummins CES 20081, Cummins CES 20086, DAF PSQL 2.1E LD, DDC 93K222, DTFR 13D110 (MB 235.28), Deutz TTCD-Motors, Ford WSS-M2C 213-A1, IVECO 18-1804 TLS E6, Liebherr LH-00-ENG LA, MAN M 3271-1, MAN M 3297-1, MAN M 3477, MAN M 3575, MAN M 3691, MAN M 3777, MB 228.31, MB 228.51, MB 235.28, MTU Type 2.1, Scania Low Ash, Voith Retarder B, Volvo CNG |
Cummins CES 20081, Cummins CES 20086, DAF PSQL 2.1E LD, DDC 93K222, DTFR 13D110 (MB 235.28), Deutz TTCD-Motors, Ford WSS-M2C 213-A1, IVECO 18-1804 TLS E6, Liebherr LH-00-ENG LA, MAN M 3271-1, MAN M 3297-1, MAN M 3477, MAN M 3575, MAN M 3691, MAN M 3777, MB 228.31, MB 228.51, MB 235.28, MTU Type 2.1, Scania Low Ash, Voith Retarder B, Volvo CNG
|
||
| Density at 20 °C | g/cm³ | 852 | EN ISO 12185 |
852
g/cm³
EN ISO 12185
|
| Color | Brown | visual |
Brown
visual
|
|
| Viscosity at 100 °C | mm²/s | 12.2 | DIN 51562-1 |
12.2
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 73.6 | DIN 51562-1 |
73.6
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 164 | DIN ISO 2909 |
164
DIN ISO 2909
|
|
| CCS Viscosity at -30 °C | mPa*s | 5900 | ASTM D5293 |
5900
mPa*s
ASTM D5293
|
| Low Temp. Pumping viscosity (MRV) at -35 °C | mPa*s | 21.500 | ASTM D4684 |
21.500
mPa*s
ASTM D4684
|
| Noack Volatility | % | 11.8 | ASTM D5800 |
11.8
%
ASTM D5800
|
| tbn | mgKOH/g | 13.9 | ASTM D2896 |
13.9
mgKOH/g
ASTM D2896
|
| Approvals | Caterpillar ECF-3, Cummins CES 20081, Cummins CES 20086, DAF PSQL 2.1E LD, DDC 93K222, DTFR 13D110 (MB 235.28), DTFR 15C100, DTFR 15C110, DTFR 15C120, Deutz DQC IV-18 LA, Deutz TTCD-Motors, Ford WSS-M2C 213-A1, IVECO 18-1804 TLS E6, Liebherr LH-00-ENG LA, MAN M 3271-1, MAN M 3297-1, MAN M 3477, MAN M 3575, MAN M 3677, MAN M 3691, MAN M 3777, MB 228.31, MB 228.51, MB 235.28, MTU Type 2.1, MTU Type 3.1, Mack EOS-4.5, Renault RLD-3, Scania LDF-4, Scania Low Ash, Voith Retarder B, Volvo CNG, Volvo VDS-4.5 |
Caterpillar ECF-3, Cummins CES 20081, Cummins CES 20086, DAF PSQL 2.1E LD, DDC 93K222, DTFR 13D110 (MB 235.28), DTFR 15C100, DTFR 15C110, DTFR 15C120, Deutz DQC IV-18 LA, Deutz TTCD-Motors, Ford WSS-M2C 213-A1, IVECO 18-1804 TLS E6, Liebherr LH-00-ENG LA, MAN M 3271-1, MAN M 3297-1, MAN M 3477, MAN M 3575, MAN M 3677, MAN M 3691, MAN M 3777, MB 228.31, MB 228.51, MB 235.28, MTU Type 2.1, MTU Type 3.1, Mack EOS-4.5, Renault RLD-3, Scania LDF-4, Scania Low Ash, Voith Retarder B, Volvo CNG, Volvo VDS-4.5
|
||
| Recommendations | Cummins CES 20081, Cummins CES 20086, DAF PSQL 2.1E LD, DTFR 13D110 (MB 235.28), Detroit Diesel DDC 93K222, Deutz TTCD Motors, Ford WSS-M2C213 A1, IVECO 18-1804 TLS E6, JASO DH-2, Liebherr LH-00-ENG LA, MAN 3297-1, MAN 3691, MAN M 3271-1, MAN M 3477, MAN M 3575, MAN M 3777, MB 228.31, MB 228.51, MB 235.28, MTU Typ 2.1, Scania LowAsh, VOLVO CNG, Voith Retarder B |
Cummins CES 20081, Cummins CES 20086, DAF PSQL 2.1E LD, DTFR 13D110 (MB 235.28), Detroit Diesel DDC 93K222, Deutz TTCD Motors, Ford WSS-M2C213 A1, IVECO 18-1804 TLS E6, JASO DH-2, Liebherr LH-00-ENG LA, MAN 3297-1, MAN 3691, MAN M 3271-1, MAN M 3477, MAN M 3575, MAN M 3777, MB 228.31, MB 228.51, MB 235.28, MTU Typ 2.1, Scania LowAsh, VOLVO CNG, Voith Retarder B
|
RAVENOL EURO IV Truck SAE 10W-40
For mixed park
RAVENOL EURO IV Truck SAE 10W-40 is a universal multi-grade low friction oil on the basis of synthetic base oils in connection with the most modern additives for all diesel engines with and without turbo charging for trucks, buses and working machines and is coordinated to the latest generation of 4-Takt diesel engines.
Manufacturer Approved:
DTFR 15C110, Deutz DQC IV-10 LA, Mack EO-N, Renault RLD-2, Tatra TDS 30/12, Volvo VDS-3
Compliance with the requirements:
DAF HP-2, MAN M 3277, MAN M 3477, MB 228.51, MTU Type 3, MTU Type 3.1, Renault RXD, Scania LDF
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1122107-001
Volume:
5 L
Vendor code:
1122107-005
1122107-005-01-999
Code:
4014835725959
Volume:
10 L
Vendor code:
1122107-010
1122107-010-01-999
Code:
4014835725942
Volume:
20 L
Vendor code:
1122107-020
1122107-020-01-999
Code:
4014835725928
Volume:
20 L, ecobox
Vendor code:
1122107-B20
Volume:
60 L
Vendor code:
1122107-060
1122107-060-01-999
Code:
4014835725966
Volume:
60 L, print
Vendor code:
1122107-D60
1122107-D60-01-888
Code:
4014835725935
Volume:
208 L
Vendor code:
1122107-208
1122107-208-01-999
Code:
4014835725980
Volume:
208 L, print
Vendor code:
1122107-D28
1122107-D28-01-888
Code:
4014835725904
Volume:
1000 L
Vendor code:
1122107-700
RAVENOL EURO IV Truck SAE 10W-40 is UHPD-Motoroil (Ultra High Performance Diesel) with special requirements for Diesel Particular Filters DPF for the LOW SPAsh Technology. Offers low content of sulphur, phosphor and low ash content.
Application instructions
RAVENOL EURO IV Truck SAE 10W-40 is maximum efficiency engine oil which can be used the whole year and which was produced for the new exhaust gas emission directives respectively for vehicles with exhaust gas return systems.
RAVENOL EURO IV Truck SAE 10W-40 can be used in all diesel engines with and without turbo charging. Suitable for EURO I, II, III, IV and EURO V engines.
Characteristics
- High corrosion protection
- An excellent oxidation stability
- An excellent high temperature stability
- Excellent detergent and dispersant characteristics
- Profitability because of a low fuel consumption
- Long endurance because of a high oxidation stability
- An excellent cold start behaviour, a quick engine lubrication at low temperatures
- A very good viscosity temperature behaviour
- Neutrality of sealing
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 10W-40 |
10W-40
|
||
| Type | Semi-synthetic |
Semi-synthetic
|
||
| API | CI-4 |
CI-4
|
||
| ACEA | E6, E7 |
E6, E7
|
||
| Manufacturer Approved | DTFR 15C110, Deutz DQC IV-10 LA, Mack EO-N, Renault RLD-2, Tatra TDS 30/12, Volvo VDS-3 |
DTFR 15C110, Deutz DQC IV-10 LA, Mack EO-N, Renault RLD-2, Tatra TDS 30/12, Volvo VDS-3
|
||
| Recomendations | DAF HP-2, MAN M 3277, MAN M 3477, MB 228.51, MTU Type 3, MTU Type 3.1, Renault RXD, Scania LDF |
DAF HP-2, MAN M 3277, MAN M 3477, MB 228.51, MTU Type 3, MTU Type 3.1, Renault RXD, Scania LDF
|
||
| Density at 20 °C | g/cm³ | 856 | EN ISO 12185 |
856
g/cm³
EN ISO 12185
|
| Color | Brown | visual |
Brown
visual
|
|
| Viscosity at 100 °C | mm²/s | 14.7 | DIN 51562-1 |
14.7
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 99.3 | DIN 51562-1 |
99.3
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 153 | DIN ISO 2909 |
153
DIN ISO 2909
|
|
| CCS Viscosity at -25 °C | mPa*s | 6600 | ASTM D5293 |
6600
mPa*s
ASTM D5293
|
| Low Temp. Pumping viscosity (MRV) at -30 °C | mPa*s | 19.700 | ASTM D4684 |
19.700
mPa*s
ASTM D4684
|
| Noack Volatility | % | 6.7 | ASTM D5800 |
6.7
%
ASTM D5800
|
| tbn | mgKOH/g | 10.4 | ASTM D2896 |
10.4
mgKOH/g
ASTM D2896
|
| Approvals | DAF HP-2, DTFR 15C110, Deutz DQC IV-10 LA, MAN M 3277, MAN M 3477, MB 228.51, MTU Type 3, MTU Type 3.1, Mack EO-N, Renault RLD-2, Renault RXD, Scania LDF, Tatra TDS 30/12, Volvo VDS-3 |
DAF HP-2, DTFR 15C110, Deutz DQC IV-10 LA, MAN M 3277, MAN M 3477, MB 228.51, MTU Type 3, MTU Type 3.1, Mack EO-N, Renault RLD-2, Renault RXD, Scania LDF, Tatra TDS 30/12, Volvo VDS-3
|
||
| Recommendations | DAF HP-2, MAN M 3277 (CRF Abgasrückführung), MAN M 3477, MB 228.51, MTU Typ 3, MTU Typ 3.1, Renault RXD, Scania LDF |
DAF HP-2, MAN M 3277 (CRF Abgasrückführung), MAN M 3477, MB 228.51, MTU Typ 3, MTU Typ 3.1, Renault RXD, Scania LDF
|
Engine oil
RAVENOL Expert SHPD SAE 10W-40 is a easy running engine oil for the use in heavily used induction motors, turbo diesel engines. Selected active ingredients ensure maximum engine cleanliness, even in short-haul traffic. The mixture of unconventional as well as HC basic oils, synthetic components and modern additives guarantees longest oil change intervals and a high corrosion protection at a low oil and fuel consumption.
Manufacturer Approved:
Cummins CES 20077, Cummins CES 20078, DTFR 15B110, Deutz DQC III-10, MTU Type 2, Mack EO-M Plus, Mack EO-N, Renault RLD-2, TEDOM 258-3, Volvo VDS-3
Compliance with the requirements:
Allison C-4, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Global DHD-1, MAN M 3275-1, MB 228.3, MB 229.1, Scania LDF, VW 500.00, VW 505.00, Voith Retarder B
- Available packaging
- Product parameters
Volume:
1000 L
Vendor code:
1122105-700
RAVENOL Expert SHPD SAE 10W-40 has an excellent flow behaviour even at low temperatures. The quick reach of critical lubrication points provides a considerable corrosion reduction during the warm-up period. Exclusive additives guarantee the best engine cleanness even at short distances.
Application instructions
RAVENOL Expert SHPD SAE 10W-40 is low-friction long-life engine oil for all kind of diesel engines with and without turbocharging in trucks, buses and machinery. Suitable for the longest oil change intervals.
Characteristics
- Excellent detergent and dispersant characteristics
- Low evaporation
- A high ageing stability
- Protection of reflecting surface formation
- Very good cold start characteristics
- Reduces oil and fuel consumption
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 10W-40 |
10W-40
|
||
| Type | Semi-synthetic |
Semi-synthetic
|
||
| API | CI-4, SL |
CI-4, SL
|
||
| ACEA | A3, B4, E4, E7 |
A3, B4, E4, E7
|
||
| Manufacturer Approved | Cummins CES 20077, Cummins CES 20078, DTFR 15B110, Deutz DQC III-10, MTU Type 2, Mack EO-M Plus, Mack EO-N, Renault RLD-2, TEDOM 258-3, Volvo VDS-3 |
Cummins CES 20077, Cummins CES 20078, DTFR 15B110, Deutz DQC III-10, MTU Type 2, Mack EO-M Plus, Mack EO-N, Renault RLD-2, TEDOM 258-3, Volvo VDS-3
|
||
| Recomendations | Allison C-4, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Global DHD-1, MAN M 3275-1, MB 228.3, MB 229.1, Scania LDF, VW 500.00, VW 505.00, Voith Retarder B |
Allison C-4, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Global DHD-1, MAN M 3275-1, MB 228.3, MB 229.1, Scania LDF, VW 500.00, VW 505.00, Voith Retarder B
|
||
| Suitable for | DAF, IVECO, YaMZ |
DAF, IVECO, YaMZ
|
||
| Density at 20 °C | g/cm³ | 862 | EN ISO 12185 |
862
g/cm³
EN ISO 12185
|
| Color | Brown | visual |
Brown
visual
|
|
| Viscosity at 100 °C | mm²/s | 15.4 | DIN 51562-1 |
15.4
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 109.7 | DIN 51562-1 |
109.7
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 155 | DIN ISO 2909 |
155
DIN ISO 2909
|
|
| CCS Viscosity at -25 °C | mPa*s | 6480 | ASTM D5293 |
6480
mPa*s
ASTM D5293
|
| Noack Volatility | % | 7.3 | ASTM D5800 |
7.3
%
ASTM D5800
|
| tbn | mgKOH/g | 11 | ASTM D2896 |
11
mgKOH/g
ASTM D2896
|
| Approvals | Allison C-4, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 15B110, Deutz DQC III-10, Global DHD-1, MAN M 3275-1, MB 228.3, MB 229.1, MTU Type 2, Mack EO-M Plus, Mack EO-N, Renault RLD-2, Scania LDF, TEDOM 258-3, VW 500.00, VW 505.00, Voith Retarder B, Volvo VDS-3 |
Allison C-4, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 15B110, Deutz DQC III-10, Global DHD-1, MAN M 3275-1, MB 228.3, MB 229.1, MTU Type 2, Mack EO-M Plus, Mack EO-N, Renault RLD-2, Scania LDF, TEDOM 258-3, VW 500.00, VW 505.00, Voith Retarder B, Volvo VDS-3
|
||
| Recommendations | Allison C4, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, DAF, Global DHD-1, IVECO, MAN M 3275-1, MB 228.3, MB 229.1, Scania LDF, VW 500 00, VW 505 00, Voith Retarder B |
Allison C4, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, DAF, Global DHD-1, IVECO, MAN M 3275-1, MB 228.3, MB 229.1, Scania LDF, VW 500 00, VW 505 00, Voith Retarder B
|
RAVENOL EDT Extra Duty Truck SAE 5W-30
For trucks
RAVENOL Extra Duty Truck SAE 5W-30 is a synthetic fuel-saving "Low SAPS" heavy duty engine oil based on the latest additive technology with selected base oils. It was specially developed for diesel engines in the toughest conditions in all seasons. It is extremely well suited to use in EURO IV, EURO V and EURO VI engines in combination with low-sulfur diesel fuel. The viscosity range SAE 5W-30 ensures a reliable cold start at low outside temperatures and fully lubricity at high operating temperatures. Friction losses and wear are reduced.
Manufacturer Approved:
DAF PSQL 2.1E (-LD), DTFR 15C110, DTFR 15C120, MAN M 3677, MAN M 3691, MAN M 3775, Mack EOS-4.5, Renault RLD-3, Scania LDF-4, Volvo VDS-4.5
Compliance with the requirements:
Caterpillar ECF-3, Cummins CES 20086, DAF PSQL 2.4 LD, DDC 93K222, Deutz DQC IV-18 LA, Ford WSS-M2C 213-A, MAN M 3271-1, MAN M 3477, MB 228.51, MB 228.52, MTU Type 3.1, Volvo VDS-5
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1121106-001
Volume:
5 L
Vendor code:
1121106-005
Volume:
10 L
Vendor code:
1121106-010
1121106-010-01-999
Code:
4014835875845
Volume:
20 L
Vendor code:
1121106-020
1121106-020-01-999
Code:
4014835875913
Volume:
20 L, ecobox
Vendor code:
1121106-B20
Volume:
60 L
Vendor code:
1121106-060
Volume:
60 L, print
Vendor code:
1121106-D60
Volume:
208 L
Vendor code:
1121106-208
1121106-208-01-999
Code:
4014835876026
Volume:
208 L, print
Vendor code:
1121106-D28
Volume:
1000 L
Vendor code:
1121106-700
RAVENOL Extra Duty Truck SAE 5W-30 is suitable for use in engines with and without particle filters and catalytic converters and is designed for the special requirements of the Low SAPS technology. The product offers low sulphur, phosphorous and ash content.
RAVENOL Extra Duty Truck SAE 5W-30 is characterized by increased oxidation and shear stability as well as improved air release characteristics to meet and exceed the latest API CK-4 requirements.
Application instructions
RAVENOL Extra Duty Truck SAE 5W-30 is a high-performance engine oil which can be used all year round and which has been designed to meet the new exhaust gas emissions guidelines. It has been created for vehicles with exhaust gas recirculation systems. Extended oil change intervals in accordance with manufacturer instructions.
RAVENOL Extra Duty Truck SAE 5W-30 is particularly suitable for use in a mixed fleet including EURO IV, EURO V and EURO VI engines and therefore offers the ideal solution to reducing the range of products needed. Please follow the manufacturer’s recommendations!
Characteristics
- Very stable and excellent viscosity behavior and high shear stability
- Fuel saving under all operating conditions
- Maintains the efficiency of the exhaust gas purification systems over a very long term
- Power losses caused by diesel particulate filters are prevented and a higher efficiency is achieved
- Low evaporation tendency resulting in low oil consumption
- Extended oil change intervals protect natural resources
- An excellent cold start behaviour
- Low SAPS = Low Sulphated ash, Phosphorous and Sulfur
- Can also be used in many commercial vehicles without diesel particulate filters
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 5W-30 |
5W-30
|
||
| Type | Synthetic |
Synthetic
|
||
| API | CI-4 Plus, CK-4, SN |
CI-4 Plus, CK-4, SN
|
||
| ACEA | E11, E6, E7, E8, E9 |
E11, E6, E7, E8, E9
|
||
| JASO | DH-2 |
DH-2
|
||
| Manufacturer Approved | DAF PSQL 2.1E (-LD), DTFR 15C110, DTFR 15C120, MAN M 3677, MAN M 3691, MAN M 3775, Mack EOS-4.5, Renault RLD-3, Scania LDF-4, Volvo VDS-4.5 |
DAF PSQL 2.1E (-LD), DTFR 15C110, DTFR 15C120, MAN M 3677, MAN M 3691, MAN M 3775, Mack EOS-4.5, Renault RLD-3, Scania LDF-4, Volvo VDS-4.5
|
||
| Recomendations | Caterpillar ECF-3, Cummins CES 20086, DAF PSQL 2.4 LD, DDC 93K222, Deutz DQC IV-18 LA, Ford WSS-M2C 213-A, MAN M 3271-1, MAN M 3477, MB 228.51, MB 228.52, MTU Type 3.1, Volvo VDS-5 |
Caterpillar ECF-3, Cummins CES 20086, DAF PSQL 2.4 LD, DDC 93K222, Deutz DQC IV-18 LA, Ford WSS-M2C 213-A, MAN M 3271-1, MAN M 3477, MB 228.51, MB 228.52, MTU Type 3.1, Volvo VDS-5
|
||
| Density at 20 °C | g/cm³ | 852.6 | EN ISO 12185 |
852.6
g/cm³
EN ISO 12185
|
| Color | Brown | visual |
Brown
visual
|
|
| Viscosity at 100 °C | mm²/s | 12.2 | DIN 51562-1 |
12.2
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 73.6 | DIN 51562-1 |
73.6
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 164 | DIN ISO 2909 |
164
DIN ISO 2909
|
|
| CCS Viscosity at -30 °C | mPa*s | 5994 | ASTM D5293 |
5994
mPa*s
ASTM D5293
|
| Low Temp. Pumping viscosity (MRV) at -35 °C | mPa*s | 19.800 | ASTM D4684 |
19.800
mPa*s
ASTM D4684
|
| Noack Volatility | % | 11.8 | ASTM D5800 |
11.8
%
ASTM D5800
|
| tbn | mgKOH/g | 9.6 | ASTM D2896 |
9.6
mgKOH/g
ASTM D2896
|
| Approvals | Caterpillar ECF-3, Cummins CES 20086, DAF PSQL 2.1E (-LD), DAF PSQL 2.4 LD, DDC 93K222, DTFR 15C110, DTFR 15C120, Deutz DQC IV-18 LA, Ford WSS-M2C 213-A, MAN M 3271-1, MAN M 3477, MAN M 3677, MAN M 3691, MAN M 3775, MB 228.51, MB 228.52, MTU Type 3.1, Mack EOS-4.5, Renault RLD-3, Scania LDF-4, Volvo VDS-4.5, Volvo VDS-5 |
Caterpillar ECF-3, Cummins CES 20086, DAF PSQL 2.1E (-LD), DAF PSQL 2.4 LD, DDC 93K222, DTFR 15C110, DTFR 15C120, Deutz DQC IV-18 LA, Ford WSS-M2C 213-A, MAN M 3271-1, MAN M 3477, MAN M 3677, MAN M 3691, MAN M 3775, MB 228.51, MB 228.52, MTU Type 3.1, Mack EOS-4.5, Renault RLD-3, Scania LDF-4, Volvo VDS-4.5, Volvo VDS-5
|
||
| Recommendations | Caterpillar ECF-3, Cummins CES 20086, DAF PSQL 2.4 LD, Detroit Diesel DDC 93K222, Deutz DQC IV-18 LA, Ford WSS-M2C213-A, MAN M 3271-1, MAN M 3477, MB 228.51, MB 228.52, MTU Typ 3.1, VOLVO VDS-5 |
Caterpillar ECF-3, Cummins CES 20086, DAF PSQL 2.4 LD, Detroit Diesel DDC 93K222, Deutz DQC IV-18 LA, Ford WSS-M2C213-A, MAN M 3271-1, MAN M 3477, MB 228.51, MB 228.52, MTU Typ 3.1, VOLVO VDS-5
|
For engine
RAVENOL NDT Nord Duty Truck SAE 5W-40 is a full synthetic all-season multi-grade engine oil based on PAO, which is used in heavy-duty diesel engines of commercial vehicles, pick-ups and SUVs.
Manufacturer Approved:
Cummins CES 20081, DDC 93K218
Compliance with the requirements:
Chrysler MS-10902, DDC 93K214, DDC 93K215, DTFR 15C100 (MB 228.31), Ford WSS-M2C 171-E, MTU Type 2, Mack EO-O Premium Plus, Renault RLD-3, Volvo VDS-4
- Available packaging
- Product parameters
Volume:
20 L
Vendor code:
1122103-020
Volume:
1000 L
Vendor code:
1122103-700
RAVENOL NDT Nord Duty Truck SAE 5W-40 can be used in new low-emission engines with exhaust gas after-treatment.
RAVENOL NDT Nord Duty Truck SAE 5W-40 delivers reduced friction, wear and fuel consumption and ensures extended oil change intervals up to 80.000 km in turbo-diesel engines.
RAVENOL NDT Nord Duty Truck SAE 5W-40 improves engine performance, reliability and cleanness thanks to active agents that retain excellent viscosity.
Application instructions
RAVENOL NDT Nord Duty Truck SAE 5W-40 is used in the viscosity grade SAE 5W-40 by engine manufacturers as an all-season, multi-grade engine oil in in heavy duty diesel engines of commercial vehicles with exhaust gas after-treatment.
RAVENOL NDT Nord Duty Truck SAE 5W-4 is the preferred recommendation of manufacturers for turbo diesel engines due to the extended oil change intervals up to 80.000 km.
Characteristics
- an extremely high pressure absorption
- very high oxidation stability
- an excellent aging resistance
- outstanding viscosity temperature characteristics
- high safety reserves also under marginal lubricating conditions
- suitable for extended oil change intervals
- ideally suited for demanding operating conditions
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 5W-40 |
5W-40
|
||
| Type | Full synthetic |
Full synthetic
|
||
| API | CJ-4, SM |
CJ-4, SM
|
||
| ACEA | E7, E9 |
E7, E9
|
||
| Manufacturer Approved | Cummins CES 20081, DDC 93K218 |
Cummins CES 20081, DDC 93K218
|
||
| Recomendations | Chrysler MS-10902, DDC 93K214, DDC 93K215, DTFR 15C100 (MB 228.31), Ford WSS-M2C 171-E, MTU Type 2, Mack EO-O Premium Plus, Renault RLD-3, Volvo VDS-4 |
Chrysler MS-10902, DDC 93K214, DDC 93K215, DTFR 15C100 (MB 228.31), Ford WSS-M2C 171-E, MTU Type 2, Mack EO-O Premium Plus, Renault RLD-3, Volvo VDS-4
|
||
| Density at 20 °C | g/cm³ | 849 | EN ISO 12185 |
849
g/cm³
EN ISO 12185
|
| Color | Brown | visual |
Brown
visual
|
|
| Viscosity at 100 °C | mm²/s | 14.45 | DIN 51562-1 |
14.45
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 89.7 | DIN 51562-1 |
89.7
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 167 | DIN ISO 2909 |
167
DIN ISO 2909
|
|
| CCS Viscosity at -30 °C | mPa*s | 4957 | ASTM D5293 |
4957
mPa*s
ASTM D5293
|
| Low Temp. Pumping viscosity (MRV) at -35 °C | mPa*s | 26.600 | ASTM D4684 |
26.600
mPa*s
ASTM D4684
|
| Noack Volatility | % | 10.4 | ASTM D5800 |
10.4
%
ASTM D5800
|
| tbn | mgKOH/g | 10.1 | ASTM D2896 |
10.1
mgKOH/g
ASTM D2896
|
| Approvals | Chrysler MS-10902, Cummins CES 20081, DDC 93K214, DDC 93K215, DDC 93K218, DTFR 15C100 (MB 228.31), Ford WSS-M2C 171-E, MTU Type 2, Mack EO-O Premium Plus, Renault RLD-3, Volvo VDS-4 |
Chrysler MS-10902, Cummins CES 20081, DDC 93K214, DDC 93K215, DDC 93K218, DTFR 15C100 (MB 228.31), Ford WSS-M2C 171-E, MTU Type 2, Mack EO-O Premium Plus, Renault RLD-3, Volvo VDS-4
|
||
| Recommendations | Chrysler MS-10902, DTFR 15C100 (MB 228.31), Detroit Diesel DDC 93K214, Detroit Diesel DDC 93K215, Ford WSS-M2C171-E, MTU Typ 2, Mack EO-O PP (Premium Plus), Renault VI RLD-3, VOLVO VDS-4 |
Chrysler MS-10902, DTFR 15C100 (MB 228.31), Detroit Diesel DDC 93K214, Detroit Diesel DDC 93K215, Ford WSS-M2C171-E, MTU Typ 2, Mack EO-O PP (Premium Plus), Renault VI RLD-3, VOLVO VDS-4
|
Mechanical gearbox
RAVENOL Catoel TO-4 SAE 50
For transmission
RAVENOL CATOEL TO-4 SAE 50 is a special transmission oil developed specifically to meet the stringent requirements of the Caterpillar TO-4 specification. It ensures maximum wear protection in different gears, like side drives and differentials optimized friction coefficient in the power-shift transmissions, wet brakes and clutches and provides maximum service life of the units.
Compliance with the requirements:
Allison C-4, Caterpillar FD-1, Caterpillar TO-4, Caterpillar TO-4M, Komatsu KES 07.868.1 (2002), ZF TE-ML 03C, ZF TE-ML 07F
- Available packaging
- Product parameters
Volume:
20 L
Vendor code:
1310615-020
Volume:
208 L
Vendor code:
1310615-208
1310615-208-01-999
Volume:
1000 L
Vendor code:
1310615-700
Application instructions
RAVENOL CATOEL TO-4 SAE 50 is formulated to meet the stringent Caterpillar TO-4 specification, and is suitable for use in transmissions, final drives, hydraulic systems, wet brakes and clutches that require this specification of lubricant.
Characteristics
- Highest wear protection.
- High oxidation stability.
- Excellent viscosity-temperature behavior.
- Optimization of friction coefficient behavior.
- Guarantees maximum life of the units.
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 50W |
50W
|
||
| Type | Mineral |
Mineral
|
||
| API | CF, MT-1 |
CF, MT-1
|
||
| Recomendations | Allison C-4, Caterpillar FD-1, Caterpillar TO-4, Caterpillar TO-4M, Komatsu KES 07.868.1 (2002), ZF TE-ML 03C, ZF TE-ML 07F |
Allison C-4, Caterpillar FD-1, Caterpillar TO-4, Caterpillar TO-4M, Komatsu KES 07.868.1 (2002), ZF TE-ML 03C, ZF TE-ML 07F
|
||
| Suitable for | Eaton Fuller |
Eaton Fuller
|
||
| Density at 20 °C | g/cm³ | 894 | EN ISO 12185 |
894
g/cm³
EN ISO 12185
|
| Color | tan | visual |
tan
visual
|
|
| Viscosity at 100 °C | mm²/s | 16.75 | DIN 51562-1 |
16.75
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 183.9 | DIN 51562-1 |
183.9
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 96 | DIN ISO 2909 |
96
DIN ISO 2909
|
|
| Approvals | Allison C-4, Caterpillar FD-1, Caterpillar TO-4, Caterpillar TO-4M, Komatsu KES 07.868.1 (2002), ZF TE-ML 03C, ZF TE-ML 07F |
Allison C-4, Caterpillar FD-1, Caterpillar TO-4, Caterpillar TO-4M, Komatsu KES 07.868.1 (2002), ZF TE-ML 03C, ZF TE-ML 07F
|
||
| Recommendations | Allison C4, Caterpillar FD-1, Caterpillar TO-4, Caterpillar TO-4M, Eaton Fuller, Komatsu KES 07.868.1 (2002), ZF TE-ML 03C, ZF TE-ML 07F |
Allison C4, Caterpillar FD-1, Caterpillar TO-4, Caterpillar TO-4M, Eaton Fuller, Komatsu KES 07.868.1 (2002), ZF TE-ML 03C, ZF TE-ML 07F
|
Power steering
RAVENOL ATF Dexron D II
For automatic transmission
RAVENOL ATF Dexron D II is a first class transmission fluid for automatic transmissions of all vehicles and working machines on the basis of high refined mineral oils with a corresponding additive treatment.
Manufacturer Approved:
Voith H55.6335.xx
Compliance with the requirements:
Caterpillar TO-2, DTFR 13C140 (MB 236.7), Ford ESD-M2C 185-A, Ford ESP-M2C 138-CJ, Ford ESP-M2C 166-H, Ford MERCON®, Ford SQM-9010B, MAN 339 Type Z1, MB 236.6, MB 236.7, Renk Doromat, ZF TE-ML 03D, ZF TE-ML 04D, ZF TE-ML 05L, ZF TE-ML 11A, ZF TE-ML 14A, ZF TE-ML 17C
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1213102-001
1213102-001-01-999
Code:
4014835733510
Volume:
4 L
Vendor code:
1213102-004
1213102-004-01-999
Code:
4014835733596
Volume:
10 L
Vendor code:
1213102-010
1213102-010-01-999
Code:
4014835733541
Volume:
20 L
Vendor code:
1213102-020
1213102-020-01-999
Code:
4014835733527
Volume:
20 L, ecobox
Vendor code:
1213102-B20
1213102-B20-01-888
Code:
4014835787827
Volume:
60 L
Vendor code:
1213102-060
1213102-060-01-999
Code:
4014835733565
Volume:
208 L
Vendor code:
1213102-208
1213102-208-01-999
Code:
4014835733589
Volume:
208 L, print
Vendor code:
1213102-D28
Volume:
1000 L
Vendor code:
1213102-700
Application instructions
RAVENOL ATF Dexron D II was developed for the use in automatic transmissions, hydro steering mechanisms, converters and power transmissions and can be used as a universal ATF (Automatic-Transmission-Fluid) for all vehicles and working machines.
Characteristics
- protection against corrosion, sludge and sticking
- an excellent and very shear stable viscosity temperature behaviour
- no problems concerning very low respectively very high temperatures
- an excellent high thermal capacity
- free of foam even under hardest loads
- neutral behaviour against sealing materials
- mixable and compatible with all kinds of ATF
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| Type | Mineral |
Mineral
|
||
| Manufacturer Approved | Voith H55.6335.xx |
Voith H55.6335.xx
|
||
| Recomendations | Caterpillar TO-2, DTFR 13C140 (MB 236.7), Ford ESD-M2C 185-A, Ford ESP-M2C 138-CJ, Ford ESP-M2C 166-H, Ford MERCON®, Ford SQM-9010B, MAN 339 Type Z1, MB 236.6, MB 236.7, Renk Doromat, ZF TE-ML 03D, ZF TE-ML 04D, ZF TE-ML 05L, ZF TE-ML 11A, ZF TE-ML 14A, ZF TE-ML 17C |
Caterpillar TO-2, DTFR 13C140 (MB 236.7), Ford ESD-M2C 185-A, Ford ESP-M2C 138-CJ, Ford ESP-M2C 166-H, Ford MERCON®, Ford SQM-9010B, MAN 339 Type Z1, MB 236.6, MB 236.7, Renk Doromat, ZF TE-ML 03D, ZF TE-ML 04D, ZF TE-ML 05L, ZF TE-ML 11A, ZF TE-ML 14A, ZF TE-ML 17C
|
||
| specification | Allison C-3, Allison C-4, GM Dexron® II D |
Allison C-3, Allison C-4, GM Dexron® II D
|
||
| Suitable for | CVT |
CVT
|
||
| Density at 20 °C | g/cm³ | 848 | EN ISO 12185 |
848
g/cm³
EN ISO 12185
|
| Color | Red | visual |
Red
visual
|
|
| Viscosity at 100 °C | mm²/s | 7.3 | DIN 51562-1 |
7.3
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 34.3 | DIN 51562-1 |
34.3
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 185 | DIN ISO 2909 |
185
DIN ISO 2909
|
|
| Approvals | Allison C-3, Allison C-4, Caterpillar TO-2, DTFR 13C140 (MB 236.7), Ford ESD-M2C 185-A, Ford ESP-M2C 138-CJ, Ford ESP-M2C 166-H, Ford MERCON®, Ford SQM-9010B, GM Dexron® II D, MAN 339 Type Z1, MB 236.6, MB 236.7, Renk Doromat, Voith H55.6335.xx, ZF TE-ML 03D, ZF TE-ML 04D, ZF TE-ML 05L, ZF TE-ML 11A, ZF TE-ML 14A, ZF TE-ML 17C |
Allison C-3, Allison C-4, Caterpillar TO-2, DTFR 13C140 (MB 236.7), Ford ESD-M2C 185-A, Ford ESP-M2C 138-CJ, Ford ESP-M2C 166-H, Ford MERCON®, Ford SQM-9010B, GM Dexron® II D, MAN 339 Type Z1, MB 236.6, MB 236.7, Renk Doromat, Voith H55.6335.xx, ZF TE-ML 03D, ZF TE-ML 04D, ZF TE-ML 05L, ZF TE-ML 11A, ZF TE-ML 14A, ZF TE-ML 17C
|
||
| Recommendations | CVT, Caterpillar TO-2, DTFR 13C140 (MB 236.7), Ford M2C-138 CJ, Ford M2C-166H, Ford M2C-185A, Ford MERCON®, Ford SQM-9010B, MAN 339 Z1, MB 236.6, MB 236.7, Renk Doromat, ZF TE-ML 03D, ZF TE-ML 04D, ZF TE-ML 05L, ZF TE-ML 11A, ZF TE-ML 14A, ZF TE-ML 17C |
CVT, Caterpillar TO-2, DTFR 13C140 (MB 236.7), Ford M2C-138 CJ, Ford M2C-166H, Ford M2C-185A, Ford MERCON®, Ford SQM-9010B, MAN 339 Z1, MB 236.6, MB 236.7, Renk Doromat, ZF TE-ML 03D, ZF TE-ML 04D, ZF TE-ML 05L, ZF TE-ML 11A, ZF TE-ML 14A, ZF TE-ML 17C
|
||
| ATF | Dexron D II |
Dexron D II
|
Cooling system
RAVENOL TTC Premix -40°C Protect C11
Coolant
RAVENOL TTC Trad. Techn. Coolant Premix -40°C is a ready to use, prediluted eco-friendly 1.2- Ethanediol (monoethylene glycol) based nitrite, amine and phosphate-free coolant for cooling circuits in combustion engines which provides maintenance-free corrosion and frost protection. The product is formulated as a long-term coolant based on a proven inhibitor development.
Compliance with the requirements:
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
- Available packaging
- Product parameters
Volume:
1.5 L
Vendor code:
1410105-150
1410105-150-01-999
Code:
4014835755314
Volume:
5 L
Vendor code:
1410105-005
1410105-005-01-999
Code:
4014835755352
Volume:
20 L
Vendor code:
1410105-020
1410105-020-01-999
Code:
4014835755321
Volume:
20 L, ecobox
Vendor code:
1410105-B20
1410105-B20-01-888
Code:
4014835855939
Volume:
60 L
Vendor code:
1410105-060
1410105-060-01-999
Code:
4014835755369
Volume:
208 L
Vendor code:
1410105-208
1410105-208-01-999
Code:
4014835755383
Volume:
1000 L
Vendor code:
1410105-700
The quality of an antifreeze is no longer just determined by the antifreeze effect (which automatically exists in an ethylene-glycol based product), but by the rust protection.
That is why manufacturers subject antifreeze to lengthy corrosion and cavitation tests.
RAVENOL TTC Trad. Techn. Coolant Premix -40°C protects the cooling system from rust, frost, and in summer, from overheating.
Application instructions
RAVENOL TTC Trad. Techn. Coolant Premix -40°C is a prediluted coolant with frost and rust protection for year-round use in automotive engines.
Even in summer coolant must contain enough antifreeze to ensure good corrosion and overheating protection.
Instructions: Add RAVENOL TTC Trad. Techn. Coolant Premix -40°C to radiator to fill line.
Characteristics
- Excellent for light metal engines
- Good reserve alkalinity
- High-quality corrosion additives for optimal corrosion protection
- Elastomer compatible with elastome
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| ASTM | D1384, D2570, D2809, D3306, D4985, D6210 Type 1-FF |
D1384, D2570, D2809, D3306, D4985, D6210 Type 1-FF
|
||
| Recomendations | AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C |
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
|
||
| Suitable for | Suzuki |
Suzuki
|
||
| Density at 20 °C | g/cm³ | 1080 | EN ISO 12185 |
1080
g/cm³
EN ISO 12185
|
| Color | yellow green | visual |
yellow green
visual
|
|
| pH - value at 20 °C | 7,8 | ASTM D1287 |
7,8
ASTM D1287
|
|
| Freezing point | °C | -40 | ASTM D1177 |
-40
°C
ASTM D1177
|
| Approvals | AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C |
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
|
||
| Recommendations | AFNOR R15-601, ASTM D1384, ASTM D2570, ASTM D2809, ASTM D3306, ASTM D4985, ASTM D6210 Type 1-FF, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 NF, O Norm V 5123 (Österreich), SAE J1034, Suzuki, UNE 25-361 (Spanien), VW TL 774-C (entspricht G11) |
AFNOR R15-601, ASTM D1384, ASTM D2570, ASTM D2809, ASTM D3306, ASTM D4985, ASTM D6210 Type 1-FF, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 NF, O Norm V 5123 (Österreich), SAE J1034, Suzuki, UNE 25-361 (Spanien), VW TL 774-C (entspricht G11)
|
RAVENOL HDT Heavy Duty Truck Cool. Concentrate
Coolant
RAVENOL Fließverbesserer
- Product parameters
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
RAVENOL Fließverbesserer
are:complete restless burningno erosion of the flammabilityno change of the hazard categoryno r eduction of the viscosity, no illegal wastage in the pumpApplication note:Diesel fuel and fuel o il EL must have a temperature of more than 5°C when
RAVENOL Fließverbesserer
is used (this is given when the goods are stored in an underground tank!).
RAVENOL Fließverbesserer
itself must have a temperature of more than 0°C in case of use. Therefore, don’t store it outside.
RAVENOL Fließverbesserer
will become viscous below 0°C – this will not influence the product quality.Please follow!In or der to guarantee an optimum mixing the diesel fuel should have a temperature of more than 0°C and th e fuel oil EL more than 5°C. As the average temperatures are between 6°C and 9°C in case of a normal underground tank storage and diesel fuel and fuel oil EL are normally delivered with higher tempera tures than the annual average it satisfies to pour the necessary quantity of
RAVENOL Fließverbesserer
into the fixed tank or vehicle tank before the vehicle is fuelled. The “splash” during the filling of the vehicle secures the necessary stable mixing.Concerning overground positioned tanks approxim ately the half of diesel fuel or fuel oil quantity should be poured during the filling. If there is a deposit in the tank before filling a mixing with a temperature of more than 0°C can be secured. T hen the necessary quantity of
RAVENOL Fließverbesserer
has to be poured and afterwards the second half of diesel fuel or fuel oil has to be tanked.After having added
RAVENOL Fließverbesserer
(after having fuelled!) the engine of vehicles and working machines has to run approximately 10 min utes. Hereby it is secured that the
RAVENOL Fließverbesserer
reaches the fuel filter and the injection pump and can be effective there. This prevents starting p roblems.ATTENTION!Before use in common rail or pump injector vehicles be sure to read the operati ng instructions of the vehicle and follow the instructions of the vehicle manufacturer!
RAVENOL TTC Concentrate Protect C11
Coolant
RAVENOL TTC Trad. Techn. Coolant Concentrate is an eco-friendly 1.2- Ethanediol (monoethylene glycol) based nitrite, amine and phosphate-free coolant for cooling circuits in combustion engines which provides maintenance-free corrosion and frost protection. The product is formulated as a long-term coolant based on a proven inhibitor development.
Compliance with the requirements:
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
- Available packaging
- Product parameters
Volume:
1.5 L
Vendor code:
1410100-150
1410100-150-01-999
Code:
4014835755215
Volume:
5 L
Vendor code:
1410100-005
1410100-005-01-999
Code:
4014835755253
Volume:
10 L
Vendor code:
1410100-010
Volume:
20 L
Vendor code:
1410100-020
1410100-020-01-999
Code:
4014835755222
Volume:
20 L, ecobox
Vendor code:
1410100-B20
Volume:
60 L
Vendor code:
1410100-060
1410100-060-01-999
Code:
4014835755260
Volume:
60 L, plastic
Vendor code:
1410100-060-01-995
Code:
4014835755239
Volume:
60 L, print
Vendor code:
1410100-D60
Volume:
208 L
Vendor code:
1410100-208
1410100-208-01-995
Code:
4014835755208
Volume:
1000 L
Vendor code:
1410100-700
It is no longer just the anti-freeze effect (which automatically exists in an ethylene-glycol based product) which is critical for the quality of a coolant, but also the rust protection.
Therefore manufacturers subject coolants to long corrosion and cavitation tests.
RAVENOL TTC Trad. Techn. Coolant Concentrate protects the cooling system from corrosion, frost, and in the summer from overheating.
Application instructions
RAVENOL TTC Trad. Techn. Coolant Concentrate with frost and rust protection. Use according to the mixing chart. Follow manufacturer’s recommendations.
Even in summer coolant must contain enough antifreeze to ensure good corrosion and overheating protection.
Instructions: Clean cooling system, check for leaks, flush.
Mix RAVENOL TTC Trad. Techn. Coolant Concentrate with distilled water (per mixing chart) and add. Allow engine and heater to warm up, add coolant to fill level.
| Table of mixing ratios | ||
|---|---|---|
| Antifreeze protection until | Parts Antifreeze | Parts Water |
| -20°C | 35% | 65% |
| -37°C | 50% | 50% |
| -50°C | 60% | 40% |
Characteristics
- Excellent for light metal engines
- Good reserve alkalinity
- High-quality corrosion additives for optimal corrosion protection
- Elastomer compatible with elastomers used in automotive radiators
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| ASTM | D1384, D2809, D3306, D4340, D4985, D6210 Type 1-FF |
D1384, D2809, D3306, D4340, D4985, D6210 Type 1-FF
|
||
| Recomendations | AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C |
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
|
||
| Suitable for | Suzuki |
Suzuki
|
||
| Density at 20 °C | g/cm³ | 1130 | EN ISO 12185 |
1130
g/cm³
EN ISO 12185
|
| Color | yellow green | visual |
yellow green
visual
|
|
| Freezing point (50 % solution) | °C | -37 | ASTM D1177 |
-37
°C
ASTM D1177
|
| pH - value at 20 °C (50 Vol %) | 8,4 | ASTM D1287 |
8,4
ASTM D1287
|
|
| Approvals | AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C |
AFNOR R15-601, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97 B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 Type NF, O Norm V 5123, SAE J 1034, UNE 25-361 (Spanien), VW TL 774-C
|
||
| Recommendations | AFNOR R15-601, ASTM D1384, ASTM D2809, ASTM D3306, ASTM D4340, ASTM D4985, ASTM D6210 Type 1-FF, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 NF, O Norm V 5123 (Österreich), SAE J1034, Suzuki, UNE 25-361 (Spanien), VW TL 774-C (entspricht G11) |
AFNOR R15-601, ASTM D1384, ASTM D2809, ASTM D3306, ASTM D4340, ASTM D4985, ASTM D6210 Type 1-FF, BS 6580 (GB), CUNA NC 956-16 (Italien), Chrysler MS-7170, Fiat 9.55523, Fiat PARAFLU 11, Ford WSS-M97B51-A1, IVECO 18-1830, JIS K 2234 (Japan), MAN 324 NF, O Norm V 5123 (Österreich), SAE J1034, Suzuki, UNE 25-361 (Spanien), VW TL 774-C (entspricht G11)
|
RAVENOL destilliertes Wasser
For batteries
RAVENOL destilliertes Wasser is deionised distilled water and is manufactured using the ion exchangerprocess.
Compliance with the requirements:
DIN 43530-4, DIN EN 50272
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1360010-001
1360010-001-01-000
Code:
4014835300453
Volume:
5 L
Vendor code:
1360010-005
1360010-005-01-000
Code:
4014835300507
Volume:
5 L, specialist. canister
Vendor code:
1360010-005
1360010-005-01-001
Code:
4014835300514
Volume:
208 L
Vendor code:
1360010-208
Volume:
1000 L
Vendor code:
1360010-700
Volume:
20 L
Vendor code:
1360010-020
1360010-020-01-001
Code:
4014835300422
In the course of this process, the water flows through a column filled with ion exchange resin. This has theability to exchange its accumulated ions for the ions present in the water.
As the ion exchange resin cannot accumulate an infinite number of ions, they have to be “revived”, i.e. theyhave to be regenerated. This takes place using the currently most commonly used regeneration agents: sodiumchloride (water softening), hydrochloric acid (cation exchange) and sodium hydroxide (anion exchange).The conductivity of the water flowing through is constantly checked in a fully automated process and the ionexchanger unit regulates itself automatically.
RAVENOL destilliertes Wasser deionised water is regularly checked by taking samples.
Application instructions
RAVENOL destilliertes Wasser is ideally suited to filling up vehicle batteries and for steam irons and aquariums (to reduce the hardness of the water).
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| Recomendations | DIN 43530-4, DIN EN 50272 |
DIN 43530-4, DIN EN 50272
|
||
| Approvals | DIN 43530-4, DIN EN 50272 |
DIN 43530-4, DIN EN 50272
|
||
| Recommendations | DIN 43 530-4 Akkumulatoren, DIN EN 50272, Elektrolyt und Nachfüllwasser |
DIN 43 530-4 Akkumulatoren, DIN EN 50272, Elektrolyt und Nachfüllwasser
|