Search by VIN, equipment make, model, type or unit name, or by the part number of any oil:
Oil for Komatsu, Wheel loaders, W/WA, WA65-6 (Komatsu 4D95LWE-5)
Komatsu Model (Wheel loaders, W/WA) to find out what kind of oil is used for it
Komatsu Wheel loaders, W/WA WA65-6 (Komatsu 4D95LWE-5)from 2008 Engine oil, automatic transmission fluid, manual transmission oil, antifreeze, brake fluid, power steering fluid and other fluids.
Power:
Engine Komatsu 4D95LWE-5
For engine
RAVENOL Super Performance Truck SAE 5W-30 is a high alloyed USHPD low friction engine oil for commercial vehicles. Because of the use of synthetic basic oils the viscosity area 5W-30 could be realised. Because of the cold viscosity SAE 5W a definite cold start (low cold start corrosion) and a supply of all lubrication areas is guaranteed as quickly as possible at very low outside temperatures. Extreme stress applications are controlled by the high temperature viscosity SAE 30. Minimized friction loss and wear.
Manufacturer Approved:
Renault RXD
Compliance with the requirements:
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, MAN M 3277, MB 228.5, MB 235.28, MTU Type 3, Mack EO-M Plus, Scania LDF-3, Voith Retarder B, Volvo VDS-3
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1122102-001
Volume:
20 L, ecobox
Vendor code:
1122102-B20
Volume:
60 L
Vendor code:
1122102-060
Volume:
1000 L
Vendor code:
1122102-700
Application instructions
RAVENOL Super Performance Truck SAE 5W-30 is a high-performance engine oil for commercial vehicles which can be used the whole year and which is adapted to the new exhaust gas emission rules (also for EURO I, II, III, IV and EURO V engines).
RAVENOL Super Performance Truck SAE 5W-3 is suitable for oil change intervals up to more than 100.000 km according to the manufacturer’s specifications.
Characteristics
- Protection against corrosion
- An excellent oxidation stability
- An excellent high temperature stability
- Excellent detergent and dispersant attributes
- Profitability because of a low fuel consumption
- Long endurance because of a high oxidation stability
- Excellent cold start attributes
- A very good viscosity temperature behaviour
- Low evaporation
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 5W-30 |
5W-30
|
||
| Type | Semi-synthetic |
Semi-synthetic
|
||
| API | CF, CI-4 |
CF, CI-4
|
||
| ACEA | E4, E7 |
E4, E7
|
||
| JASO | DH-1 |
DH-1
|
||
| Manufacturer Approved | Renault RXD |
Renault RXD
|
||
| Recomendations | Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, MAN M 3277, MB 228.5, MB 235.28, MTU Type 3, Mack EO-M Plus, Scania LDF-3, Voith Retarder B, Volvo VDS-3 |
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, MAN M 3277, MB 228.5, MB 235.28, MTU Type 3, Mack EO-M Plus, Scania LDF-3, Voith Retarder B, Volvo VDS-3
|
||
| Suitable for | IVECO |
IVECO
|
||
| Density at 20 °C | g/cm³ | 854 | EN ISO 12185 |
854
g/cm³
EN ISO 12185
|
| Color | tan | visual |
tan
visual
|
|
| Viscosity at 100 °C | mm²/s | 11.5 | DIN 51562-1 |
11.5
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 69.3 | DIN 51562-1 |
69.3
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 161 | DIN ISO 2909 |
161
DIN ISO 2909
|
|
| CCS Viscosity at -30 °C | mPa*s | 6000 | ASTM D5293 |
6000
mPa*s
ASTM D5293
|
| Low Temp. Pumping viscosity (MRV) at -35 °C | mPa*s | 16.200 | ASTM D4684 |
16.200
mPa*s
ASTM D4684
|
| Noack Volatility | % | 10.1 | ASTM D5800 |
10.1
%
ASTM D5800
|
| tbn | mgKOH/g | 13 | ASTM D2896 |
13
mgKOH/g
ASTM D2896
|
| Approvals | Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, MAN M 3277, MB 228.5, MB 235.28, MTU Type 3, Mack EO-M Plus, Renault RXD, Scania LDF-3, Voith Retarder B, Volvo VDS-3 |
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, MAN M 3277, MB 228.5, MB 235.28, MTU Type 3, Mack EO-M Plus, Renault RXD, Scania LDF-3, Voith Retarder B, Volvo VDS-3
|
||
| Recommendations | Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, IVECO, JASO DH-1, MAN M 3277, MB 228.5, MB 235.28, MTU Typ 3, Mack EO-M Plus, Scania LDF-3, VOLVO VDS-3, Voith Retarder B |
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 13D110 (MB 235.28), DTFR 15B120 (MB 228.5), Global DHD-1, IVECO, JASO DH-1, MAN M 3277, MB 228.5, MB 235.28, MTU Typ 3, Mack EO-M Plus, Scania LDF-3, VOLVO VDS-3, Voith Retarder B
|
For mixed fleet
RAVENOL Turbo plus SHPD SAE 15W-40 is SHPD-motor oil for the mixed automobile fleet.
Manufacturer Approved:
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 15B110, Deutz DQC III-10, MTU Type 2, Renault RLD, Renault RLD-2, TEDOM 258-3, Volvo VDS-3
Compliance with the requirements:
Allison C-4, Caterpillar TO-2, Global DHD-1, John Deere JDQ-78 A, MAN M 3275-1, MB 228.3, MB 229.1, Mack EO-M, Mack EO-M Plus, Scania LDF-2, ZF TE-ML 07C
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1123115-001
1123115-001-01-999
Volume:
4 L
Vendor code:
1123115-004
Volume:
7 L
Vendor code:
1123115-007
1123115-007-01-999
Volume:
1000 L
Vendor code:
1123115-700
1123115-700-01-999
RAVENOL Turbo plus SHPD SAE 15W-40 can be used for diesel and petrol engines, also with turbochargers.
RAVENOL Turbo plus SHPD SAE 15W-40 has been especially developed for extended oil change intervals, according to manufacturer’s recommendations.
Application instructions
RAVENOL Turbo-Plus SHPD SAE 15W-40 is recommended by the engine manufacturers for extended oil change intervals as SAE 15W-40 multigrade engine oil in heavy duty commercial vehicle diesel engines.
RAVENOL Turbo-Plus SHPD SAE 15W-40 is the preferred use for extended oil life in turbo charged diesel engines according to manufacturer’s recommendations.
Characteristics
- Extremely high pressure absorption capacity
- Very high oxidation stability
- Excellent aging stability
- Excellent viscosity and temperature behaviour
- High security reserves even under limited lubrication circumstances
- Suitable for extended oil change intervals
- Suitable for heavy operating conditions
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 15W-40 |
15W-40
|
||
| Type | Mineral |
Mineral
|
||
| API | CI-4, SL |
CI-4, SL
|
||
| ACEA | A3, B4, E7 |
A3, B4, E7
|
||
| JASO | DH-1 |
DH-1
|
||
| Manufacturer Approved | Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 15B110, Deutz DQC III-10, MTU Type 2, Renault RLD, Renault RLD-2, TEDOM 258-3, Volvo VDS-3 |
Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 15B110, Deutz DQC III-10, MTU Type 2, Renault RLD, Renault RLD-2, TEDOM 258-3, Volvo VDS-3
|
||
| Recomendations | Allison C-4, Caterpillar TO-2, Global DHD-1, John Deere JDQ-78 A, MAN M 3275-1, MB 228.3, MB 229.1, Mack EO-M, Mack EO-M Plus, Scania LDF-2, ZF TE-ML 07C |
Allison C-4, Caterpillar TO-2, Global DHD-1, John Deere JDQ-78 A, MAN M 3275-1, MB 228.3, MB 229.1, Mack EO-M, Mack EO-M Plus, Scania LDF-2, ZF TE-ML 07C
|
||
| Suitable for | IVECO, Steyr Motor GAZ 560, YaMZ |
IVECO, Steyr Motor GAZ 560, YaMZ
|
||
| Density at 20 °C | g/cm³ | 870 | EN ISO 12185 |
870
g/cm³
EN ISO 12185
|
| Color | tan | visual |
tan
visual
|
|
| Viscosity at 100 °C | mm²/s | 15 | DIN 51562-1 |
15
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 115.7 | DIN 51562-1 |
115.7
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 134 | DIN ISO 2909 |
134
DIN ISO 2909
|
|
| tbn | mgKOH/g | 10.5 | ASTM D2896 |
10.5
mgKOH/g
ASTM D2896
|
| Approvals | Allison C-4, Caterpillar TO-2, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 15B110, Deutz DQC III-10, Global DHD-1, John Deere JDQ-78 A, MAN M 3275-1, MB 228.3, MB 229.1, MTU Type 2, Mack EO-M, Mack EO-M Plus, Renault RLD, Renault RLD-2, Scania LDF-2, TEDOM 258-3, Volvo VDS-3, ZF TE-ML 07C |
Allison C-4, Caterpillar TO-2, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DTFR 15B110, Deutz DQC III-10, Global DHD-1, John Deere JDQ-78 A, MAN M 3275-1, MB 228.3, MB 229.1, MTU Type 2, Mack EO-M, Mack EO-M Plus, Renault RLD, Renault RLD-2, Scania LDF-2, TEDOM 258-3, Volvo VDS-3, ZF TE-ML 07C
|
||
| Recommendations | Allison C4, Caterpillar TO-2, Global DHD-1, IVECO, JASO DH-1, John Deere JDQ-78A, MAN M 3275-1 (Multigrades), MB 228.3, MB 229.1, Mack EO-M, Mack EO-M Plus, Scania LDF-2, ZF TE-ML 07C |
Allison C4, Caterpillar TO-2, Global DHD-1, IVECO, JASO DH-1, John Deere JDQ-78A, MAN M 3275-1 (Multigrades), MB 228.3, MB 229.1, Mack EO-M, Mack EO-M Plus, Scania LDF-2, ZF TE-ML 07C
|
RAVENOL Turbo Plus SHPD SAE 10W-30
For mixed park
RAVENOL Turbo Plus SHPD SAE 10W-30 is high performance multi-grade oil for use in petrol and diesel engines including turbo versions.
Compliance with the requirements:
Caterpillar ECF-2, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DDC 93K215, DTFR 15B110 (MB 228.3), Deutz DQC III-10, Global DHD-1, MAN M 3275-1, MB 228.3, MTU Type 2, MTU Type 3, Mack EO-N, Renault RLD, Renault RLD-2, Volvo VDS-3
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1123105-001
Volume:
10 L
Vendor code:
1123105-010
1123105-010-01-999
Code:
4014835737747
Volume:
20 L
Vendor code:
1123105-020
1123105-020-01-999
Code:
4014835637726
Volume:
20 L, ecobox
Vendor code:
1123105-B20
Volume:
60 L
Vendor code:
1123105-060
1123105-060-01-999
Code:
4014835737761
Volume:
208 L
Vendor code:
1123105-208
1123105-208-01-999
Code:
4014835737785
Volume:
1000 L
Vendor code:
1123105-700
Volume:
5 L
Vendor code:
1123105-005
1123105-005-01-999
RAVENOL Turbo Plus SHPD SAE 10W-30 meets the requirements of SAE-Class 10W-30. This adjustment of viscosity also ensures a good lubricating film at high temperatures.
RAVENOL Turbo Plus SHPD SAE 10W-30 is particularly suitable for engines with already high performance.
Application instructions
RAVENOL Turbo Plus SHPD SAE 10W-30 is approved, tried and tested for aggregates specifying:
Specifications: API CI-4/ SL, ACEA E7, E5, E3, ACEA A3/B4
Approval: YaMZ
Recommendations: Caterpillar ECF-2, TO-2; Cummins CES 20071, -72, -76, -77, -78; DAF; DDC 93K215; Deutz DQC III-10; Global DHD-1; JASO DH-1; Mack EO-N; MAN M 3275-1; MB 228.3;MTU Type 2, MTU Type 3; Renault RLD, Renault VI RLD-2; Volvo VDS 3.
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 10W-30 |
10W-30
|
||
| Type | Mineral |
Mineral
|
||
| API | CI-4, SL |
CI-4, SL
|
||
| ACEA | A3, B4, E3, E5, E7 |
A3, B4, E3, E5, E7
|
||
| JASO | DH-1 |
DH-1
|
||
| Recomendations | Caterpillar ECF-2, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DDC 93K215, DTFR 15B110 (MB 228.3), Deutz DQC III-10, Global DHD-1, MAN M 3275-1, MB 228.3, MTU Type 2, MTU Type 3, Mack EO-N, Renault RLD, Renault RLD-2, Volvo VDS-3 |
Caterpillar ECF-2, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DDC 93K215, DTFR 15B110 (MB 228.3), Deutz DQC III-10, Global DHD-1, MAN M 3275-1, MB 228.3, MTU Type 2, MTU Type 3, Mack EO-N, Renault RLD, Renault RLD-2, Volvo VDS-3
|
||
| Suitable for | DAF, YaMZ |
DAF, YaMZ
|
||
| Density at 20 °C | g/cm³ | 865 | EN ISO 12185 |
865
g/cm³
EN ISO 12185
|
| Color | tan | visual |
tan
visual
|
|
| Viscosity at 100 °C | mm²/s | 12 | DIN 51562-1 |
12
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 74.9 | DIN 51562-1 |
74.9
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 156 | DIN ISO 2909 |
156
DIN ISO 2909
|
|
| tbn | mgKOH/g | 10.2 | ASTM D2896 |
10.2
mgKOH/g
ASTM D2896
|
| Approvals | Caterpillar ECF-2, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DDC 93K215, DTFR 15B110 (MB 228.3), Deutz DQC III-10, Global DHD-1, MAN M 3275-1, MB 228.3, MTU Type 2, MTU Type 3, Mack EO-N, Renault RLD, Renault RLD-2, Volvo VDS-3 |
Caterpillar ECF-2, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DDC 93K215, DTFR 15B110 (MB 228.3), Deutz DQC III-10, Global DHD-1, MAN M 3275-1, MB 228.3, MTU Type 2, MTU Type 3, Mack EO-N, Renault RLD, Renault RLD-2, Volvo VDS-3
|
||
| Recommendations | Caterpillar ECF-2, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DAF, DTFR 15B110 (MB 228.3), Detroit Diesel DDC 93K215, Deutz DQC III-10, Global DHD-1, JASO DH-1, MAN M 3275-1, MB 228.3, MTU Typ 2, MTU Typ 3, Mack EO-N, Renault RLD, Renault VI RLD-2, VOLVO VDS-3 |
Caterpillar ECF-2, Caterpillar TO-2, Cummins CES 20071, Cummins CES 20072, Cummins CES 20076, Cummins CES 20077, Cummins CES 20078, DAF, DTFR 15B110 (MB 228.3), Detroit Diesel DDC 93K215, Deutz DQC III-10, Global DHD-1, JASO DH-1, MAN M 3275-1, MB 228.3, MTU Typ 2, MTU Typ 3, Mack EO-N, Renault RLD, Renault VI RLD-2, VOLVO VDS-3
|
Transfer case
RAVENOL UTTO Arctic
For tractors
RAVENOL Fließverbesserer
- Product parameters
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
RAVENOL Fließverbesserer
are:complete restless burningno erosion of the flammabilityno change of the hazard categoryno r eduction of the viscosity, no illegal wastage in the pumpApplication note:Diesel fuel and fuel o il EL must have a temperature of more than 5°C when
RAVENOL Fließverbesserer
is used (this is given when the goods are stored in an underground tank!).
RAVENOL Fließverbesserer
itself must have a temperature of more than 0°C in case of use. Therefore, don’t store it outside.
RAVENOL Fließverbesserer
will become viscous below 0°C – this will not influence the product quality.Please follow!In or der to guarantee an optimum mixing the diesel fuel should have a temperature of more than 0°C and th e fuel oil EL more than 5°C. As the average temperatures are between 6°C and 9°C in case of a normal underground tank storage and diesel fuel and fuel oil EL are normally delivered with higher tempera tures than the annual average it satisfies to pour the necessary quantity of
RAVENOL Fließverbesserer
into the fixed tank or vehicle tank before the vehicle is fuelled. The “splash” during the filling of the vehicle secures the necessary stable mixing.Concerning overground positioned tanks approxim ately the half of diesel fuel or fuel oil quantity should be poured during the filling. If there is a deposit in the tank before filling a mixing with a temperature of more than 0°C can be secured. T hen the necessary quantity of
RAVENOL Fließverbesserer
has to be poured and afterwards the second half of diesel fuel or fuel oil has to be tanked.After having added
RAVENOL Fließverbesserer
(after having fuelled!) the engine of vehicles and working machines has to run approximately 10 min utes. Hereby it is secured that the
RAVENOL Fließverbesserer
reaches the fuel filter and the injection pump and can be effective there. This prevents starting p roblems.ATTENTION!Before use in common rail or pump injector vehicles be sure to read the operati ng instructions of the vehicle and follow the instructions of the vehicle manufacturer!
For differentials
RAVENOL Getriebeoel LS SAE 75W-90 is a synthetic lubricant for mechanical transmissions.
Compliance with the requirements:
ZF TE-ML 05C, ZF TE-ML 05D
- Available packaging
- Product parameters
Volume:
20 L
Vendor code:
1222102-020
Volume:
208 L
Vendor code:
1222102-208
Volume:
1000 L
Vendor code:
1222102-700
Volume:
60 L
Vendor code:
1222102-060
1222102-060-01-999
Code:
4014835734364
RAVENOL Getriebeoel LS SAE 75W-90 is designed based on high-quality solvent refined and synthetic base oils with special additive treatment and inhibition for higher stress on manual transmission oils and ensuring trouble-free transmission function.
Application instructions
RAVENOL Getriebeoel LS SAE 75W-90 was developed specifically for use in differential gear units with limited slip. It also ensures trouble-free lubrication in self-locking, hypoid geared transmissions.
Characteristics
- excellent oxidation stability
- excellent protection against rust and corrosion
- prevents foaming
- outstanding extreme pressure properties
- excellent limited slip properties
- fuel savings
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 75W-90 |
75W-90
|
||
| Type | Synthetic |
Synthetic
|
||
| API | GL-5 LS |
GL-5 LS
|
||
| Recomendations | ZF TE-ML 05C, ZF TE-ML 05D |
ZF TE-ML 05C, ZF TE-ML 05D
|
||
| specification | MIL-L-2105 D |
MIL-L-2105 D
|
||
| Density at 20 °C | g/cm³ | 839 | EN ISO 12185 |
839
g/cm³
EN ISO 12185
|
| Color | Yellow | visual |
Yellow
visual
|
|
| Viscosity at 100 °C | mm²/s | 17.1 | DIN 51562-1 |
17.1
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 102.1 | DIN 51562-1 |
102.1
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 182 | DIN ISO 2909 |
182
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 84.300 | ASTM D2983 |
84.300
mPa*s
ASTM D2983
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D |
MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D
|
||
| Recommendations | GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D |
GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D
|
Wheel reducers in front
RAVENOL UTTO Arctic
For tractors
RAVENOL Fließverbesserer
- Product parameters
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
RAVENOL Fließverbesserer
are:complete restless burningno erosion of the flammabilityno change of the hazard categoryno r eduction of the viscosity, no illegal wastage in the pumpApplication note:Diesel fuel and fuel o il EL must have a temperature of more than 5°C when
RAVENOL Fließverbesserer
is used (this is given when the goods are stored in an underground tank!).
RAVENOL Fließverbesserer
itself must have a temperature of more than 0°C in case of use. Therefore, don’t store it outside.
RAVENOL Fließverbesserer
will become viscous below 0°C – this will not influence the product quality.Please follow!In or der to guarantee an optimum mixing the diesel fuel should have a temperature of more than 0°C and th e fuel oil EL more than 5°C. As the average temperatures are between 6°C and 9°C in case of a normal underground tank storage and diesel fuel and fuel oil EL are normally delivered with higher tempera tures than the annual average it satisfies to pour the necessary quantity of
RAVENOL Fließverbesserer
into the fixed tank or vehicle tank before the vehicle is fuelled. The “splash” during the filling of the vehicle secures the necessary stable mixing.Concerning overground positioned tanks approxim ately the half of diesel fuel or fuel oil quantity should be poured during the filling. If there is a deposit in the tank before filling a mixing with a temperature of more than 0°C can be secured. T hen the necessary quantity of
RAVENOL Fließverbesserer
has to be poured and afterwards the second half of diesel fuel or fuel oil has to be tanked.After having added
RAVENOL Fließverbesserer
(after having fuelled!) the engine of vehicles and working machines has to run approximately 10 min utes. Hereby it is secured that the
RAVENOL Fließverbesserer
reaches the fuel filter and the injection pump and can be effective there. This prevents starting p roblems.ATTENTION!Before use in common rail or pump injector vehicles be sure to read the operati ng instructions of the vehicle and follow the instructions of the vehicle manufacturer!
For differentials
RAVENOL Getriebeoel LS SAE 75W-90 is a synthetic lubricant for mechanical transmissions.
Compliance with the requirements:
ZF TE-ML 05C, ZF TE-ML 05D
- Available packaging
- Product parameters
Volume:
20 L
Vendor code:
1222102-020
Volume:
208 L
Vendor code:
1222102-208
Volume:
1000 L
Vendor code:
1222102-700
Volume:
60 L
Vendor code:
1222102-060
1222102-060-01-999
Code:
4014835734364
RAVENOL Getriebeoel LS SAE 75W-90 is designed based on high-quality solvent refined and synthetic base oils with special additive treatment and inhibition for higher stress on manual transmission oils and ensuring trouble-free transmission function.
Application instructions
RAVENOL Getriebeoel LS SAE 75W-90 was developed specifically for use in differential gear units with limited slip. It also ensures trouble-free lubrication in self-locking, hypoid geared transmissions.
Characteristics
- excellent oxidation stability
- excellent protection against rust and corrosion
- prevents foaming
- outstanding extreme pressure properties
- excellent limited slip properties
- fuel savings
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 75W-90 |
75W-90
|
||
| Type | Synthetic |
Synthetic
|
||
| API | GL-5 LS |
GL-5 LS
|
||
| Recomendations | ZF TE-ML 05C, ZF TE-ML 05D |
ZF TE-ML 05C, ZF TE-ML 05D
|
||
| specification | MIL-L-2105 D |
MIL-L-2105 D
|
||
| Density at 20 °C | g/cm³ | 839 | EN ISO 12185 |
839
g/cm³
EN ISO 12185
|
| Color | Yellow | visual |
Yellow
visual
|
|
| Viscosity at 100 °C | mm²/s | 17.1 | DIN 51562-1 |
17.1
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 102.1 | DIN 51562-1 |
102.1
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 182 | DIN ISO 2909 |
182
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 84.300 | ASTM D2983 |
84.300
mPa*s
ASTM D2983
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D |
MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D
|
||
| Recommendations | GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D |
GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D
|
Wheel reducers rear
RAVENOL UTTO Arctic
For tractors
RAVENOL Fließverbesserer
- Product parameters
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
RAVENOL Fließverbesserer
are:complete restless burningno erosion of the flammabilityno change of the hazard categoryno r eduction of the viscosity, no illegal wastage in the pumpApplication note:Diesel fuel and fuel o il EL must have a temperature of more than 5°C when
RAVENOL Fließverbesserer
is used (this is given when the goods are stored in an underground tank!).
RAVENOL Fließverbesserer
itself must have a temperature of more than 0°C in case of use. Therefore, don’t store it outside.
RAVENOL Fließverbesserer
will become viscous below 0°C – this will not influence the product quality.Please follow!In or der to guarantee an optimum mixing the diesel fuel should have a temperature of more than 0°C and th e fuel oil EL more than 5°C. As the average temperatures are between 6°C and 9°C in case of a normal underground tank storage and diesel fuel and fuel oil EL are normally delivered with higher tempera tures than the annual average it satisfies to pour the necessary quantity of
RAVENOL Fließverbesserer
into the fixed tank or vehicle tank before the vehicle is fuelled. The “splash” during the filling of the vehicle secures the necessary stable mixing.Concerning overground positioned tanks approxim ately the half of diesel fuel or fuel oil quantity should be poured during the filling. If there is a deposit in the tank before filling a mixing with a temperature of more than 0°C can be secured. T hen the necessary quantity of
RAVENOL Fließverbesserer
has to be poured and afterwards the second half of diesel fuel or fuel oil has to be tanked.After having added
RAVENOL Fließverbesserer
(after having fuelled!) the engine of vehicles and working machines has to run approximately 10 min utes. Hereby it is secured that the
RAVENOL Fließverbesserer
reaches the fuel filter and the injection pump and can be effective there. This prevents starting p roblems.ATTENTION!Before use in common rail or pump injector vehicles be sure to read the operati ng instructions of the vehicle and follow the instructions of the vehicle manufacturer!
For differentials
RAVENOL Getriebeoel LS SAE 75W-90 is a synthetic lubricant for mechanical transmissions.
Compliance with the requirements:
ZF TE-ML 05C, ZF TE-ML 05D
- Available packaging
- Product parameters
Volume:
20 L
Vendor code:
1222102-020
Volume:
208 L
Vendor code:
1222102-208
Volume:
1000 L
Vendor code:
1222102-700
Volume:
60 L
Vendor code:
1222102-060
1222102-060-01-999
Code:
4014835734364
RAVENOL Getriebeoel LS SAE 75W-90 is designed based on high-quality solvent refined and synthetic base oils with special additive treatment and inhibition for higher stress on manual transmission oils and ensuring trouble-free transmission function.
Application instructions
RAVENOL Getriebeoel LS SAE 75W-90 was developed specifically for use in differential gear units with limited slip. It also ensures trouble-free lubrication in self-locking, hypoid geared transmissions.
Characteristics
- excellent oxidation stability
- excellent protection against rust and corrosion
- prevents foaming
- outstanding extreme pressure properties
- excellent limited slip properties
- fuel savings
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 75W-90 |
75W-90
|
||
| Type | Synthetic |
Synthetic
|
||
| API | GL-5 LS |
GL-5 LS
|
||
| Recomendations | ZF TE-ML 05C, ZF TE-ML 05D |
ZF TE-ML 05C, ZF TE-ML 05D
|
||
| specification | MIL-L-2105 D |
MIL-L-2105 D
|
||
| Density at 20 °C | g/cm³ | 839 | EN ISO 12185 |
839
g/cm³
EN ISO 12185
|
| Color | Yellow | visual |
Yellow
visual
|
|
| Viscosity at 100 °C | mm²/s | 17.1 | DIN 51562-1 |
17.1
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 102.1 | DIN 51562-1 |
102.1
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 182 | DIN ISO 2909 |
182
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 84.300 | ASTM D2983 |
84.300
mPa*s
ASTM D2983
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D |
MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D
|
||
| Recommendations | GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D |
GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D
|
Differential, front
RAVENOL UTTO Arctic
For tractors
RAVENOL Fließverbesserer
- Product parameters
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
RAVENOL Fließverbesserer
are:complete restless burningno erosion of the flammabilityno change of the hazard categoryno r eduction of the viscosity, no illegal wastage in the pumpApplication note:Diesel fuel and fuel o il EL must have a temperature of more than 5°C when
RAVENOL Fließverbesserer
is used (this is given when the goods are stored in an underground tank!).
RAVENOL Fließverbesserer
itself must have a temperature of more than 0°C in case of use. Therefore, don’t store it outside.
RAVENOL Fließverbesserer
will become viscous below 0°C – this will not influence the product quality.Please follow!In or der to guarantee an optimum mixing the diesel fuel should have a temperature of more than 0°C and th e fuel oil EL more than 5°C. As the average temperatures are between 6°C and 9°C in case of a normal underground tank storage and diesel fuel and fuel oil EL are normally delivered with higher tempera tures than the annual average it satisfies to pour the necessary quantity of
RAVENOL Fließverbesserer
into the fixed tank or vehicle tank before the vehicle is fuelled. The “splash” during the filling of the vehicle secures the necessary stable mixing.Concerning overground positioned tanks approxim ately the half of diesel fuel or fuel oil quantity should be poured during the filling. If there is a deposit in the tank before filling a mixing with a temperature of more than 0°C can be secured. T hen the necessary quantity of
RAVENOL Fließverbesserer
has to be poured and afterwards the second half of diesel fuel or fuel oil has to be tanked.After having added
RAVENOL Fließverbesserer
(after having fuelled!) the engine of vehicles and working machines has to run approximately 10 min utes. Hereby it is secured that the
RAVENOL Fließverbesserer
reaches the fuel filter and the injection pump and can be effective there. This prevents starting p roblems.ATTENTION!Before use in common rail or pump injector vehicles be sure to read the operati ng instructions of the vehicle and follow the instructions of the vehicle manufacturer!
For differentials
RAVENOL Getriebeoel LS SAE 75W-90 is a synthetic lubricant for mechanical transmissions.
Compliance with the requirements:
ZF TE-ML 05C, ZF TE-ML 05D
- Available packaging
- Product parameters
Volume:
20 L
Vendor code:
1222102-020
Volume:
208 L
Vendor code:
1222102-208
Volume:
1000 L
Vendor code:
1222102-700
Volume:
60 L
Vendor code:
1222102-060
1222102-060-01-999
Code:
4014835734364
RAVENOL Getriebeoel LS SAE 75W-90 is designed based on high-quality solvent refined and synthetic base oils with special additive treatment and inhibition for higher stress on manual transmission oils and ensuring trouble-free transmission function.
Application instructions
RAVENOL Getriebeoel LS SAE 75W-90 was developed specifically for use in differential gear units with limited slip. It also ensures trouble-free lubrication in self-locking, hypoid geared transmissions.
Characteristics
- excellent oxidation stability
- excellent protection against rust and corrosion
- prevents foaming
- outstanding extreme pressure properties
- excellent limited slip properties
- fuel savings
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 75W-90 |
75W-90
|
||
| Type | Synthetic |
Synthetic
|
||
| API | GL-5 LS |
GL-5 LS
|
||
| Recomendations | ZF TE-ML 05C, ZF TE-ML 05D |
ZF TE-ML 05C, ZF TE-ML 05D
|
||
| specification | MIL-L-2105 D |
MIL-L-2105 D
|
||
| Density at 20 °C | g/cm³ | 839 | EN ISO 12185 |
839
g/cm³
EN ISO 12185
|
| Color | Yellow | visual |
Yellow
visual
|
|
| Viscosity at 100 °C | mm²/s | 17.1 | DIN 51562-1 |
17.1
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 102.1 | DIN 51562-1 |
102.1
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 182 | DIN ISO 2909 |
182
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 84.300 | ASTM D2983 |
84.300
mPa*s
ASTM D2983
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D |
MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D
|
||
| Recommendations | GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D |
GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D
|
Differential, rear
RAVENOL UTTO Arctic
For tractors
RAVENOL Fließverbesserer
- Product parameters
can be mixed and is compatible with all diesel fuels (except Biodiesel) as well as fuel oils EL. Hi gher dosings as recommended are harmless. Demixing won’t occur.Practical experiences show that unde r consideration of the diferent kind of diesel fuels and fuel oils EL offered on the market followin g cold properties are given. With different manufacturers of diesel fuel, the effect can vary.Ad dition: Liter RavenolFließverbesserer to LiterDiesel fuel respectively fuel oil ELOperating temp eratureSummer-Diesel fuel as well as fuel oil EL1 : 1000 *)- 10°C2 : 1000- 18°C 3 : 1000- 23°C4 : 1000- 25°CWinter-Diesel-fuel1 : 1000- 25°C2 : 100 0- 28°C3 : 1000- 31°C*) The cold properties depend on the used DK respectively fuel o il EL. When admixing in a ratio of 1:1000 normally an improvement of the cold properties by 5°C to 1 0°C are possible.Characteristics:The basic advantages of
RAVENOL Fließverbesserer
are:complete restless burningno erosion of the flammabilityno change of the hazard categoryno r eduction of the viscosity, no illegal wastage in the pumpApplication note:Diesel fuel and fuel o il EL must have a temperature of more than 5°C when
RAVENOL Fließverbesserer
is used (this is given when the goods are stored in an underground tank!).
RAVENOL Fließverbesserer
itself must have a temperature of more than 0°C in case of use. Therefore, don’t store it outside.
RAVENOL Fließverbesserer
will become viscous below 0°C – this will not influence the product quality.Please follow!In or der to guarantee an optimum mixing the diesel fuel should have a temperature of more than 0°C and th e fuel oil EL more than 5°C. As the average temperatures are between 6°C and 9°C in case of a normal underground tank storage and diesel fuel and fuel oil EL are normally delivered with higher tempera tures than the annual average it satisfies to pour the necessary quantity of
RAVENOL Fließverbesserer
into the fixed tank or vehicle tank before the vehicle is fuelled. The “splash” during the filling of the vehicle secures the necessary stable mixing.Concerning overground positioned tanks approxim ately the half of diesel fuel or fuel oil quantity should be poured during the filling. If there is a deposit in the tank before filling a mixing with a temperature of more than 0°C can be secured. T hen the necessary quantity of
RAVENOL Fließverbesserer
has to be poured and afterwards the second half of diesel fuel or fuel oil has to be tanked.After having added
RAVENOL Fließverbesserer
(after having fuelled!) the engine of vehicles and working machines has to run approximately 10 min utes. Hereby it is secured that the
RAVENOL Fließverbesserer
reaches the fuel filter and the injection pump and can be effective there. This prevents starting p roblems.ATTENTION!Before use in common rail or pump injector vehicles be sure to read the operati ng instructions of the vehicle and follow the instructions of the vehicle manufacturer!
For differentials
RAVENOL Getriebeoel LS SAE 75W-90 is a synthetic lubricant for mechanical transmissions.
Compliance with the requirements:
ZF TE-ML 05C, ZF TE-ML 05D
- Available packaging
- Product parameters
Volume:
20 L
Vendor code:
1222102-020
Volume:
208 L
Vendor code:
1222102-208
Volume:
1000 L
Vendor code:
1222102-700
Volume:
60 L
Vendor code:
1222102-060
1222102-060-01-999
Code:
4014835734364
RAVENOL Getriebeoel LS SAE 75W-90 is designed based on high-quality solvent refined and synthetic base oils with special additive treatment and inhibition for higher stress on manual transmission oils and ensuring trouble-free transmission function.
Application instructions
RAVENOL Getriebeoel LS SAE 75W-90 was developed specifically for use in differential gear units with limited slip. It also ensures trouble-free lubrication in self-locking, hypoid geared transmissions.
Characteristics
- excellent oxidation stability
- excellent protection against rust and corrosion
- prevents foaming
- outstanding extreme pressure properties
- excellent limited slip properties
- fuel savings
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 75W-90 |
75W-90
|
||
| Type | Synthetic |
Synthetic
|
||
| API | GL-5 LS |
GL-5 LS
|
||
| Recomendations | ZF TE-ML 05C, ZF TE-ML 05D |
ZF TE-ML 05C, ZF TE-ML 05D
|
||
| specification | MIL-L-2105 D |
MIL-L-2105 D
|
||
| Density at 20 °C | g/cm³ | 839 | EN ISO 12185 |
839
g/cm³
EN ISO 12185
|
| Color | Yellow | visual |
Yellow
visual
|
|
| Viscosity at 100 °C | mm²/s | 17.1 | DIN 51562-1 |
17.1
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 102.1 | DIN 51562-1 |
102.1
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 182 | DIN ISO 2909 |
182
DIN ISO 2909
|
|
| Brookfield Viscosity at -40 °C | mPa*s | 84.300 | ASTM D2983 |
84.300
mPa*s
ASTM D2983
|
| Copper Strip Test at 121 °C | 1b | ASTM D130 |
1b
ASTM D130
|
|
| Approvals | MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D |
MIL-L-2105 D, ZF TE-ML 05C, ZF TE-ML 05D
|
||
| Recommendations | GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D |
GM 1940058, GM 88862624, GM 88862625, GM 93165388, ZF TE-ML 05C, ZF TE-ML 05D
|
Hydraulic system
RAVENOL Bio-Hydraulikoel HEES 46
For hydraulics
RAVENOL BIO-Hydraulikoel HEES 46 is based on synthetic, easily biodegradable esters and a powerful, environmentally friendly combination of additives which gives the product excellent properties regarding oxidation stability, corrosion, low temperatures as well as EP behaviour.
Compliance with the requirements:
JCMAS P042 HKB, Parker Denison HF-1, Parker Denison HF-2, Parker Denison HF-6, US Vessel General Permit (VGP), VDMA 24568, VDMA 24570
SAE: 46
- Available packaging
- Product parameters
Volume:
20 L
Vendor code:
1321105-020
1321105-020-01-999
Volume:
20 L, ecobox
Vendor code:
1321105-B20
Volume:
60 L
Vendor code:
1321105-060
Volume:
208 L
Vendor code:
1321105-208
1321105-208-01-999
Volume:
1000 L
Vendor code:
1321105-700
Compared with products of vegetable triglyceride base, RAVENOL BIO-Hydraulikoel HEES 46 has much better high temperature oxidation stability.
RAVENOL BIO-Hydraulikoel HEES 46 can be used year-round due to its outstanding low-temperature behaviour and provides excellent wear and corrosion protection.
Application instructions
RAVENOL BIO-Hydraulikoel HEES 46 is used wherever there is the danger of hydraulic fluid leaking into the ground-or waste water. This includes all equipment operating in or near areas of water purification or water protection or near surface water, such as e.g. sewage treatment plants, dredging ships and floating dredges, lock hydraulics and river weirs, pipe and tunnel driving machines, hydraulic aggregates in forests and on fields, earth moving machines in water and forestry machines.
Characteristics
- Biodegradability
- Excellent corrosion protection
- Outstanding cold behaviour
- Excellent oxidation stability
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 46 |
46
|
||
| Type | Full synthetic |
Full synthetic
|
||
| Recomendations | JCMAS P042 HKB, Parker Denison HF-1, Parker Denison HF-2, Parker Denison HF-6, US Vessel General Permit (VGP), VDMA 24568, VDMA 24570 |
JCMAS P042 HKB, Parker Denison HF-1, Parker Denison HF-2, Parker Denison HF-6, US Vessel General Permit (VGP), VDMA 24568, VDMA 24570
|
||
| specification | DIN 51524-1, DIN 51524-2, DIN 51524-3, Eaton Brochure 03-401-2010, ISO 15380 HEES (Dry ISO 4263-3) |
DIN 51524-1, DIN 51524-2, DIN 51524-3, Eaton Brochure 03-401-2010, ISO 15380 HEES (Dry ISO 4263-3)
|
||
| Density at 20 °C | g/cm³ | 917 | EN ISO 12185 |
917
g/cm³
EN ISO 12185
|
| Color | Yellow | visual |
Yellow
visual
|
|
| Viscosity at 100 °C | mm²/s | 9.45 | DIN 51562-1 |
9.45
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 46 | DIN 51562-1 |
46
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 190 | DIN ISO 2909 |
190
DIN ISO 2909
|
|
| Seq. I at 24 °C | ml/ml | 10/0 | ASTM D892 |
10/0
ml/ml
ASTM D892
|
| Seq. II at 93,5 °C | ml/ml | 5/0 | ASTM D892 |
5/0
ml/ml
ASTM D892
|
| Seq. III at 24 °C after 93,5 °C | ml/ml | 10/0 | ASTM D892 |
10/0
ml/ml
ASTM D892
|
| Copper Strip Test at 121 °C | 1a | ASTM D130 |
1a
ASTM D130
|
|
| Air release at 50 °C, max. | 2 | DIN ISO 9120 |
2
DIN ISO 9120
|
|
| Approvals | DIN 51524-1, DIN 51524-2, DIN 51524-3, Eaton Brochure 03-401-2010, ISO 15380 HEES (Dry ISO 4263-3), JCMAS P042 HKB, Parker Denison HF-1, Parker Denison HF-2, Parker Denison HF-6, US Vessel General Permit (VGP), VDMA 24568, VDMA 24570 |
DIN 51524-1, DIN 51524-2, DIN 51524-3, Eaton Brochure 03-401-2010, ISO 15380 HEES (Dry ISO 4263-3), JCMAS P042 HKB, Parker Denison HF-1, Parker Denison HF-2, Parker Denison HF-6, US Vessel General Permit (VGP), VDMA 24568, VDMA 24570
|
||
| Recommendations | JCMAS P042 HKB, Parker Denison HF-1, Parker Denison HF-6 (Dry ASTM D4310), Parker Dension HF-2, US Vessel General Permit (VGP), VDMA 24568, VDMA 24570 |
JCMAS P042 HKB, Parker Denison HF-1, Parker Denison HF-6 (Dry ASTM D4310), Parker Dension HF-2, US Vessel General Permit (VGP), VDMA 24568, VDMA 24570
|
Hydraulic system
Hydraulic oil
RAVENOL Hydraulikoel TS 46 (HLP) is optimal alloyed mineral hydraulic oil with a high performance level and a wide application area of the whole industry.
Compliance with the requirements:
AFNOR NFE 48-603 HM, Bosch Rexroth RE 90220, Cetop RP 2950-S, Cetop RP 91H HM, Danieli Hydraulics, Eaton Vickers I-286-S, FZG Test A 8,3/90, Fives Cincinnati P-55, Fives Cincinnati P-70, GB 111118.1 L-HM, GM LH-02-1-04, ISO 11158 HM, JCMAS HK, MIL-PRF-17672 E, Müller , NATO H-573, Parker Denison HF-0, Parker Denison HF-1, Parker Denison HF-2, SAE MS 1004 HM, SEB 181.222, Sauer-Danfoss 520L0463, U.S. Steel 126, U.S. Steel 127, U.S. Steel 136, VDMA 24318, Vickers Pumpentest, ZF TE-ML 07H
SAE: 46
- Available packaging
- Product parameters
Volume:
1 L
Vendor code:
1323105-001
Volume:
10 L
Vendor code:
1323105-010
Volume:
20 L, ecobox
Vendor code:
1323105-B20
Volume:
208 L, print
Vendor code:
1323105-D28
RAVENOL Hydraulikoel TS 46 (HLP) with efficient additives offers an excellent corrosion protection even under extreme loads. The behaviour of sealing materials is neutral.
RAVENOL Hydraulikoel TS 46 (HLP) is characterised by good viscosity temperature behaviour, a high aging resistant and a solid corrosion protection.
Application instructions
RAVENOL Hydraulikoel TS 46 (HLP) is for universally use in all hydraulic systems.
RAVENOL Hydraulikoel TS 46 (HLP) is recommended in high performance hydraulic systems with high pressure pumps of all types, in sensitive control systems.
RAVENOL Hydraulikoel TS 46 (HLP) is used for hydraulic systems in agriculture, to supply small gearboxes and for use in circulating systems.
Characteristics
- a high performance level
- a very good viscosity temperature behaviour
- a high aging resistant
- an excellent corrosion protection
- neutrality of sealing materials
| Parameter | Unit | Value | Tests | |
|---|---|---|---|---|
| SAE | 46 |
46
|
||
| Type | Mineral |
Mineral
|
||
| ASTM | D6158 |
D6158
|
||
| Recomendations | AFNOR NFE 48-603 HM, Bosch Rexroth RE 90220, Cetop RP 2950-S, Cetop RP 91H HM, Danieli Hydraulics, Eaton Vickers I-286-S, FZG Test A 8,3/90, Fives Cincinnati P-55, Fives Cincinnati P-70, GB 111118.1 L-HM, GM LH-02-1-04, ISO 11158 HM, JCMAS HK, MIL-PRF-17672 E, Müller , NATO H-573, Parker Denison HF-0, Parker Denison HF-1, Parker Denison HF-2, SAE MS 1004 HM, SEB 181.222, Sauer-Danfoss 520L0463, U.S. Steel 126, U.S. Steel 127, U.S. Steel 136, VDMA 24318, Vickers Pumpentest, ZF TE-ML 07H |
AFNOR NFE 48-603 HM, Bosch Rexroth RE 90220, Cetop RP 2950-S, Cetop RP 91H HM, Danieli Hydraulics, Eaton Vickers I-286-S, FZG Test A 8,3/90, Fives Cincinnati P-55, Fives Cincinnati P-70, GB 111118.1 L-HM, GM LH-02-1-04, ISO 11158 HM, JCMAS HK, MIL-PRF-17672 E, Müller , NATO H-573, Parker Denison HF-0, Parker Denison HF-1, Parker Denison HF-2, SAE MS 1004 HM, SEB 181.222, Sauer-Danfoss 520L0463, U.S. Steel 126, U.S. Steel 127, U.S. Steel 136, VDMA 24318, Vickers Pumpentest, ZF TE-ML 07H
|
||
| specification | DIN 51524-2, ISO 6743-4 HM |
DIN 51524-2, ISO 6743-4 HM
|
||
| Suitable for | Arburg, Atos, Metso |
Arburg, Atos, Metso
|
||
| Density at 20 °C | g/cm³ | 857 | EN ISO 12185 |
857
g/cm³
EN ISO 12185
|
| Color | light yellow | visual |
light yellow
visual
|
|
| Viscosity at 100 °C | mm²/s | 7.2 | DIN 51562-1 |
7.2
mm²/s
DIN 51562-1
|
| Viscosity at 40 °C | mm²/s | 47 | DIN 51562-1 |
47
mm²/s
DIN 51562-1
|
| Viscosity Index VI | 113 | DIN ISO 2909 |
113
DIN ISO 2909
|
|
| Demulsification | 40ml/40ml/10min. | DIN 51757 |
40ml/40ml/10min.
DIN 51757
|
|
| Aging stability, TOST | % | 2000 | DIN 51587 |
2000
%
DIN 51587
|
| FZG-Test A/8.3/90 Damage loading step | %wt. | 12 | DIN 51354/2 |
12
%wt.
DIN 51354/2
|
| Approvals | AFNOR NFE 48-603 HM, Bosch Rexroth RE 90220, Cetop RP 2950-S, Cetop RP 91H HM, DIN 51524-2, Danieli Hydraulics, Eaton Vickers I-286-S, FZG Test A 8,3/90, Fives Cincinnati P-55, Fives Cincinnati P-70, GB 111118.1 L-HM, GM LH-02-1-04, ISO 11158 HM, ISO 6743-4 HM, JCMAS HK, MIL-PRF-17672 E, Müller , NATO H-573, Parker Denison HF-0, Parker Denison HF-1, Parker Denison HF-2, SAE MS 1004 HM, SEB 181.222, Sauer-Danfoss 520L0463, U.S. Steel 126, U.S. Steel 127, U.S. Steel 136, VDMA 24318, Vickers Pumpentest, ZF TE-ML 07H |
AFNOR NFE 48-603 HM, Bosch Rexroth RE 90220, Cetop RP 2950-S, Cetop RP 91H HM, DIN 51524-2, Danieli Hydraulics, Eaton Vickers I-286-S, FZG Test A 8,3/90, Fives Cincinnati P-55, Fives Cincinnati P-70, GB 111118.1 L-HM, GM LH-02-1-04, ISO 11158 HM, ISO 6743-4 HM, JCMAS HK, MIL-PRF-17672 E, Müller , NATO H-573, Parker Denison HF-0, Parker Denison HF-1, Parker Denison HF-2, SAE MS 1004 HM, SEB 181.222, Sauer-Danfoss 520L0463, U.S. Steel 126, U.S. Steel 127, U.S. Steel 136, VDMA 24318, Vickers Pumpentest, ZF TE-ML 07H
|
||
| Recommendations | AFNOR NFE 48-603 HM, ASTM D6158, Arburg, Atos, Bosch Rexroth RE 90220, CETOP RP 2950-S, CETOP RP 91H HM, Danieli Hydraulics, Eaton Vickers I-286-S, FZG-Test A 8,3/90, Fives Cincinnati P-55, Fives Cincinnati P-70, GB 111118.1 L-HM (conventional), GM LH-02-1-04, ISO 11158 HM, JCMAS HK, LS-2, MIL-PRF-17672 E, Metso, Müller Weingarten, NATO H-573, Parker Denison HF-0, Parker Denison HF-1, Parker Dension HF-2, SAE MS1004 HM, SEB 181.222, Sauer-Danfoss 520L0463, US Steel 126, US Steel 127, US Steel 136, VDMA 24318, Verwendung lt. Betriebsanleitung, Vickers-Pumpentest, ZF TE-ML 07H |
AFNOR NFE 48-603 HM, ASTM D6158, Arburg, Atos, Bosch Rexroth RE 90220, CETOP RP 2950-S, CETOP RP 91H HM, Danieli Hydraulics, Eaton Vickers I-286-S, FZG-Test A 8,3/90, Fives Cincinnati P-55, Fives Cincinnati P-70, GB 111118.1 L-HM (conventional), GM LH-02-1-04, ISO 11158 HM, JCMAS HK, LS-2, MIL-PRF-17672 E, Metso, Müller Weingarten, NATO H-573, Parker Denison HF-0, Parker Denison HF-1, Parker Dension HF-2, SAE MS1004 HM, SEB 181.222, Sauer-Danfoss 520L0463, US Steel 126, US Steel 127, US Steel 136, VDMA 24318, Verwendung lt. Betriebsanleitung, Vickers-Pumpentest, ZF TE-ML 07H
|